HUNTER X2-600 6-Station Sprinkler Timer Controller

1. Introducció i finalview

The Hunter X2-600 is a 6-station sprinkler timer controller designed for efficient and convenient management of irrigation systems. This controller is Wi-Fi ready, allowing for advanced scheduling and remote management when paired with the optional Hunter Hydrawise Wi-Fi module. It provides reliable performance for maintaining healthy landscapes through routine installations and real-time status updates.

2. Informació de seguretat

Please read all safety instructions before installation and operation. Failure to follow these instructions may result in property damage, personal injury, or death.

• Seguretat elèctrica: Always disconnect power to the controller before performing any wiring or maintenance. Ensure all wiring connections are secure and comply with local electrical codes.
• Ús exterior: While designed for outdoor use, protect the controller from direct water spray and extreme weather conditions to ensure longevity.
• Nens: Mantingueu el controlador fora de l'abast dels nens.
• Personal qualificat: Installation and servicing should be performed by qualified personnel where necessary.

3. Contingut del paquet

Verifiqueu que tots els elements siguin presents al paquet:

• Hunter X2-600 Controller Unit
• Cable d'alimentació (preinstal·lat)
• Maquinari de muntatge (cargols, ancoratges)
• Manual d'usuari (aquest document)

4. Configuració i instal·lació

4.1 Muntatge del controlador

Select a suitable location for mounting the controller. It should be protected from direct sunlight and extreme weather, and close to a power outlet and irrigation valves.

1. Use the provided mounting template or hold the controller against the wall and mark the top mounting hole.
2. Drill a pilot hole and insert a wall anchor if necessary.
3. Install a screw into the top hole, leaving approximately 1/8 inch (3 mm) exposed.
4. Hang the controller on the top screw.
5. Mark the locations for the two bottom mounting holes.
6. Remove the controller, drill pilot holes, and insert wall anchors.
7. Re-hang the controller and secure it with the bottom screws.

Figura 4.1: Frontal view of the Hunter X2-600 controller.

4.2 Cablejat del controlador

Ensure power is disconnected before wiring. The X2-600 supports up to 6 irrigation zones, a common wire, and sensor connections.

1. Cable comú (COM): Connect the common wire from your irrigation valves to the terminal labeled 'COM'. This is typically a white wire.
2. Cables de zona (1-6): Connect each individual zone wire from your irrigation valves to the corresponding numbered terminal (1 through 6).
3. Sensor Wires (SEN): If using a rain or soil sensor, connect its wires to the 'SEN' terminals. Refer to your sensor's manual for specific wiring.
4. 24VAC Power: The controller comes with a pre-attached power cord. Plug it into a standard 120V AC outlet. The 24VAC terminals are for optional external power sources or accessories.

Figure 4.2: Wiring terminals of the Hunter X2-600 controller.

4.3 Initial Power-Up and Wi-Fi Readiness

Once wired, connect the power cord to an electrical outlet. The controller display will illuminate. The X2-600 is Wi-Fi ready, meaning it can be upgraded to smart control by purchasing and installing a separate Hunter Hydrawise Wi-Fi module. This module plugs directly into the controller and enables remote management via the Hydrawise app.

Figura 4.3: Esquena view of the Hunter X2-600 controller with power cord.

5. Instruccions de funcionament

The X2-600 features a simple dial and button interface for programming.

5.1 Configuració de la data i l'hora

1. Turn the dial to the 'Date/Time' position.
2. Use the arrow buttons to adjust the year, month, day, hour, and minute.
3. Press the 'PRG' button to confirm each setting.

5.2 Programació de programacions de reg

The controller allows for multiple independent programs (A, B, C).

1. Seleccioneu el programa: Turn the dial to 'PRG' and use the arrow buttons to select Program A, B, or C.
2. Estableix els horaris d'inici: Turn the dial to 'Start Times'. Use the arrow buttons to set up to four start times per program.
3. Temps d'execució definits: Turn the dial to 'Run Times'. For each zone (1-6), use the arrow buttons to set the desired watering duration in minutes.
4. Establir dies d'aigua: Turn the dial to 'Water Days'. Use the arrow buttons to select specific days of the week for watering, or choose interval watering (e.g., every 2 days).

5.3 Funcionament manual

To manually run a single station or all stations:

• Turn the dial to 'Manual'.
• Use the arrow buttons to select the desired zone or 'ALL' for all zones.
• Press the 'PRG' button to start the manual run.

5.4 Ajust estacional

The 'Seasonal Adjust' feature allows you to quickly increase or decrease watering durations for all zones in a program by a percentage, without reprogramming individual run times.

• Turn the dial to 'Seasonal Adjust'.
• Use the arrow buttons to adjust the percentage (e.g., 100% for normal, 50% for half, 150% for more).

5.5 Wi-Fi Control (with optional module)

If the Hunter Hydrawise Wi-Fi module is installed, you can manage your controller remotely using the Hydrawise app on your smartphone or tablet. This includes setting schedules, monitoring water usage, and receiving alerts. Refer to the Hydrawise module's specific instructions for setup and app usage.

6. Manteniment

The Hunter X2-600 controller requires minimal maintenance.

• Neteja: Netegeu periòdicament l'exterior del controlador amb un drap suau i sec.amp tela. No utilitzeu netejadors abrasius ni dissolvents.
• Connexions: Inspeccioneu anualment totes les connexions del cablejat per assegurar-vos que estiguin ben fixades i que no presentin corrosió.
• Hivernització: In regions with freezing temperatures, disconnect the controller from power and drain the irrigation system to prevent damage from freezing water.

7. Solució De Problemes

Consulteu la taula següent per veure els problemes habituals i les seves solucions:

8. Especificacions

• Model: X2-600
• Estacions: 6
• Entrada d'alimentació: 120V AC (with attached plug)
• Sortida: 24 V AC
• Dimensions (paquet): 10.43 x 8.62 x 4.29 polzades
• Pes de l'article: 3.54 lliures
• Color: Blanc
• Nombre de configuracions: 2 (likely referring to programs A/B)
• Mida de la pantalla: 6 Inches (referring to the overall display area)
• UPC: 611698666555

9. Garantia i Suport

Hunter Industries provides a manufacturer's warranty for the X2-600 controller. For specific warranty terms, duration, and conditions, please refer to the warranty card included with your product or visit the official Hunter Industries website. For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact Hunter customer service or visit their online support resources.

Oficial de Hunter Industries Weblloc: www.hunterindustries.com