Paulmann 94453 Capea LED Outdoor Wall Lamp amb el manual d'instruccions del detector de moviment

Introducció

Thank you for choosing the Paulmann 94453 Capea LED Outdoor Wall Lamp. This manual provides essential information for the safe installation, operation, and maintenance of your new outdoor lighting fixture. Please read these instructions carefully before installation and retain them for future reference.

Image: The Paulmann Capea LED Outdoor Wall Lamp, showing the product itself and its retail packaging. The lamp is black, with a conical shade and an integrated motion sensor at the base.

Instruccions importants de seguretat

• Seguretat elèctrica: Installation must be performed by a qualified electrician in accordance with local wiring regulations. Always switch off the main power supply before installation, maintenance, or repair.
• Ús exterior: This product is designed for outdoor use (IP44 rated). Ensure all connections are properly sealed to prevent water ingress.
• Muntatge: Mount the fixture securely on a stable surface. Do not install on flammable surfaces.
• Font de llum: The LED light source is integrated and not replaceable by the user. Do not attempt to open or modify the light source compartment.
• Temperatura: No cobreixi la lamp with insulating material. Ensure adequate air circulation around the fixture.

Contingut del paquet

Verifiqueu que tots els components siguin presents abans de començar la instal·lació:

• 1x Paulmann Capea LED Outdoor Wall Lamp (Model 94453)
• Instruccions de muntatge
• Materials de muntatge (cargols, tacs de paret) - (Assumed, as typical for wall lamps)

Especificacions tècniques

Image: Technical drawing showing the dimensions of the Paulmann Capea LED Outdoor Wall Lamp: 153mm width, 165mm height, and 96mm depth.

Guia d'instal·lació

Abans de començar: Ensure the main power supply to the installation area is switched off at the circuit breaker. Use appropriate tools and safety equipment.

1. Preparació de la ubicació de muntatge: Choose a suitable wall location for the lamp, ensuring it is a stable surface and allows for proper wiring. Mark the drilling points for the mounting bracket.
2. Forats: Perforeu els forats als punts marcats i inseriu els tacs de paret adequats (si cal).
3. Suport de muntatge: Fixeu el suport de muntatge a la paret amb els cargols proporcionats.
4. Cablejat: Connect the electrical wires from your mains supply to the terminal block inside the lamp fixture. Ensure correct polarity (Live, Neutral, Earth) and secure all connections tightly. Refer to local electrical codes.
5. Adjunta Lamp: Enganxeu amb cura la lamp fixture to the mounting bracket, ensuring no wires are pinched. Secure the lamp al seu lloc.
6. Restaura l'alimentació: Un cop finalitzada la instal·lació i totes les connexions siguin segures, restableu l'alimentació a l'interruptor principal.

Image: The Paulmann Capea LED Outdoor Wall Lamp shown with its packaging, which illustrates basic installation steps and features like the motion sensor and IP44 rating.

Instruccions de funcionament

The Paulmann Capea LED Outdoor Wall Lamp features an integrated motion sensor for automatic operation.

Configuració del sensor de moviment

The motion sensor can be adjusted to suit your specific needs. Typically, there are controls for:

• Angle de detecció: Aproximadament 90 graus.
• Interval de detecció: 2-8 metres.
• Light Sensitivity (LUX): Determines the ambient light level at which the sensor activates the lamp.
  • ON < 20 Lux: El lamp will turn on when motion is detected and the ambient light is below 20 Lux (dark conditions).
  • OFF > 20 Lux: El lamp will remain off when the ambient light is above 20 Lux (daylight conditions).
• Hora ON: Sets the duration the light remains on after motion is detected. Adjustable from approximately 5 seconds to 5 minutes.

Adjust these settings using the small dials or switches located on the motion sensor unit, usually found at the bottom of the lamp. Use a small screwdriver if necessary.

Image: A diagram illustrating the motion sensor's detection angle (90 degrees), range (2-8 meters), and light sensitivity settings (On < 20 Lux / Off > 20 Lux), along with the adjustable time duration (5 seconds - 5 minutes).

Imatge: Un primer pla view of the integrated motion sensor located at the base of the Paulmann Capea LED Outdoor Wall Lamp, showing its spherical lens.

Manteniment

• Neteja: Disconnect power before cleaning. Wipe the lamp amb un suau, damp drap. No utilitzeu productes de neteja abrasius ni dissolvents, ja que poden danyar l'acabat o els components elèctrics.
• Font de llum: The LED light source is integrated and designed for long-term use (30,000 hours). It is not user-replaceable. If the LED fails, the entire fixture typically needs replacement.
• Inspecció: Inspeccioneu periòdicament la lamp for any signs of damage, loose connections, or wear. Address any issues promptly.

Resolució de problemes

Garantia i assistència al client

Paulmann products are manufactured to high quality standards. This product comes with a 5-year guarantee, as indicated on the packaging. For warranty claims, technical assistance, or further inquiries, please contact your retailer or Paulmann customer support directly. Keep your proof of purchase for warranty purposes.

For more information, visit the official Paulmann weblloc: www.paulmann.com

Informació d'eliminació

This product contains electronic components and an integrated LED light source. Do not dispose of it with general household waste. Please take it to a designated collection point for electrical and electronic equipment recycling in accordance with local regulations. Proper disposal helps prevent potential negative consequences for the environment and human health.