Schellenberg Smart DRIVE 60930 2-Channel Remote Control Instruction Manual

1. Introducció

This manual provides comprehensive instructions for the proper setup, operation, and maintenance of your Schellenberg Smart DRIVE 60930 2-channel remote control. This device is designed for convenient control of up to two compatible Schellenberg Smart DRIVE M, L, and XL garage door operators.

Figure 1: Schellenberg Smart DRIVE 60930 2-channel remote control and its packaging.

2. Informació de seguretat

• Always keep the remote control out of reach of children.
• Ensure the garage door operator is visible during operation, especially when controlled by multiple wireless handheld transmitters, to prevent accidents.
• Do not expose the remote control to extreme temperatures, moisture, or direct sunlight.
• Only use the specified battery type (CR2032 lithium button battery).
• Eliminar les bateries usades d'acord amb la normativa local.

3. Contingut del paquet

El paquet inclou els articles següents:

• 1 x Smart DRIVE Wireless Transmitter (2-channel)
• 1 x CR2032 Lithium Button Battery (pre-installed)
• 1 x Instruccions de muntatge
• 1 x Loop, yellow (pre-mounted)
• 1 x Loop, gray (additional)

Figure 2: Remote control, battery, and interchangeable loop.

4. Característiques del producte

• Comfortable control of up to 2 garage door drives.
• Easy learning process with the garage door opener.
• Operates on a radio frequency of 868.4 MHz.
• Includes an additional gray ring for color identification of the handheld transmitter.
• Compatible with Schellenberg Smart DRIVE M, L, and XL garage door automations.

5. Especificacions

Figure 3: Dimensions of the remote control.

6. Configuració i programació

6.1. Copying an Existing Remote Control (First Set Way)

This method allows you to duplicate the signal from an existing remote control to your new Schellenberg Smart DRIVE 60930 remote. Ensure both remotes are in close proximity during this process.

1. Verify that the existing remote control is functioning correctly by pressing its buttons.
2. On the new remote control, simultaneously press and hold the two top buttons (A and B) until the LED flashes.
3. Release button A while continuing to hold button B.
4. Press button A three times. The LED will flash rapidly. Release button B.
5. Place the original remote control and the new remote control side-by-side.
6. On the new remote, long-press the button you wish to program (e.g., button A). The LED will flash slowly.
7. On the original remote, long-press the corresponding button. The LED on the new remote will flash rapidly, indicating successful copying.
8. Repeat for other buttons if desired.

Video 1: This video demonstrates the 'First Set Way' for copying an existing remote control's signal to the Schellenberg Smart DRIVE 60930. It shows how to activate the copying mode on both remotes and transfer the signal.

6.2. Learning Method for Receiver (Second Set Way)

This method involves programming the remote control directly to your garage door operator's receiver unit. Refer to your garage door operator's manual for specific receiver button locations.

1. On the new remote control, simultaneously press and hold the two top buttons (A and B) until the LED flashes.
2. Release button A while continuing to hold button B.
3. Press button A three times. The LED will flash rapidly. Release button B.
4. Locate the learning button on your garage door operator's receiver.
5. Press the learning button on the receiver. The receiver's indicator light will begin to flash.
6. Within 3-5 seconds, long-press the desired button on your new Schellenberg remote control. The receiver's light will flash quickly and then go out, indicating successful learning.
7. Test the remote control to ensure it operates the garage door correctly.

Video 2: This video illustrates the 'Second Set Way' for programming the Schellenberg Smart DRIVE 60930 remote control to a receiver. It details the steps to put the receiver into learning mode and then pair the remote control.

7. Instruccions de funcionament

Once programmed, operating your Schellenberg Smart DRIVE 60930 remote control is straightforward:

• To open or close the garage door, press the corresponding programmed button on the remote control.
• Ensure you have a clear line of sight to the garage door and its operator during activation.

Figure 4: Using the remote control from inside a vehicle.

Figure 5: Activating the garage door with the remote control.

8. Manteniment

8.1. Substitució de la bateria

The remote control is powered by a CR2032 lithium button battery. If the remote control's range decreases or the LED does not light up, the battery may need to be replaced.

1. Obriu amb cura el comandament a distància casing.
2. Traieu la bateria CR2032 antiga.
3. Introduïu una pila CR2032 nova, assegurant-vos de la polaritat correcta (+/-).
4. Tanqueu el comandament a distància casing de manera segura.

8.2. Neteja

Netegeu el comandament a distància amb un drap suau i sec. No utilitzeu productes de neteja abrasius ni dissolvents.

9. Solució De Problemes

• El comandament a distància no funciona després de la programació: Ensure the programming steps were followed precisely. Try reprogramming the remote. Check the battery.
• Interval reduït: Replace the battery. Ensure there are no obstructions between the remote and the receiver. Large metal objects or other radio devices can interfere with the signal.
• El LED no s'encén: The battery may be depleted or incorrectly inserted. Replace the battery and check its polarity.

10. Garantia i Suport

For warranty information, technical support, or further assistance, please refer to the official Schellenberg weblloc web o poseu-vos en contacte amb el seu servei d'atenció al client. També podeu visitar el Schellenberg Store on Amazon per obtenir informació addicional sobre el producte i accessoris.