Waterco Waterking Chlorinator Model 25500 User Manual

Introducció

The Waterco Waterking Chlorinator Model 25500 is designed to provide efficient and consistent chlorination for your pool or spa, ensuring clean and safe water. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting to help you get the most out of your chlorinator.

Imatge: Frontal view of the Waterco Waterking Chlorinator Model 25500, showing the main body, lid, and plumbing connections.

Informació de seguretat

Please read and adhere to all safety warnings and precautions before installing, operating, or maintaining the chlorinator.

• Always read and understand all instructions before installing or operating this product.
• Wear appropriate personal protective equipment (PPE), including gloves and eye protection, when handling chlorine or other pool chemicals.
• Ensure the chlorinator is installed by a qualified professional in accordance with local codes and regulations.
• Mantenir fora de l'abast dels nens i mascotes.
• Do not mix different types of chlorine or other chemicals in the chlorinator. This can cause dangerous reactions.
• Always turn off the pool pump and close all isolation valves before opening the chlorinator or performing any maintenance.
• Never open the chlorinator while the pump is running or the system is under pressure.

Configuració i instal·lació

1. Desembalatge: Desembaleu amb cura tots els components i verifiqueu-los amb la llista d'embalatge.
2. Selecció d'ubicació: Choose a suitable location for installation. The chlorinator should typically be installed after the pool filter and heater (if present), but before any other equipment that could be damaged by concentrated chlorine. Ensure there is adequate space for maintenance and refilling.
3. Connexions de fontaneria: The Waterking Chlorinator is designed for inline installation. Ensure proper plumbing connections using appropriate PVC cement and primer for secure, leak-free joints. Pay attention to the flow direction indicated on the unit.


Imatge: Lateral view of the chlorinator, highlighting the "FLOW" arrow indicating the correct water flow direction for installation.

4. Temps de curat: Allow sufficient curing time for all plumbing connections as per the adhesive manufacturer's instructions before pressurizing the system.
5. Prova de pressió: After curing, slowly open isolation valves to pressurize the system and check for any leaks.

Imatge: Lateral view of the Waterco Waterking Chlorinator, showing the inlet and outlet connections.

Imatge: Un example of a plumbing accessory or pipe section that may be used during installation of the chlorinator.

Instruccions de funcionament

1. Preparació per al farcit: Ensure the pool pump is turned off and the system is depressurized. Turn the chlorinator's control dial to the "OFF" position.
2. Tapa oberta: Carefully unscrew the lid of the chlorinator. Be aware of any residual chlorine fumes.
3. Add Chlorine: Add only slow-dissolving trichlor tablets or sticks to the chlorinator chamber. Do not use granular chlorine, calcium hypochlorite, or other chemicals, as this can cause damage or dangerous reactions. Fill to the recommended level, typically not exceeding 80% capacity.
4. Tapa segura: Replace the lid securely, ensuring the O-ring is properly seated to create a watertight seal. Hand-tighten only.
5. Set Feed Rate: Turn the control dial to the desired "RATE OF FEED" setting. Start with a lower setting (e.g., 1 or 2) and adjust as needed based on your pool's chlorine demand and water testing results.

Imatge: Primer pla view of the chlorinator's control dial, showing settings from "OFF" to "HI" for adjusting the chlorine feed rate.
6. Inici de la bomba: Turn on your pool pump. The chlorinator will now begin dispensing chlorine into your pool water.
7. Monitor Water Chemistry: Regularly test your pool water for chlorine levels and pH. Adjust the feed rate dial as necessary to maintain optimal water chemistry (typically 1-3 ppm free chlorine and pH 7.4-7.6).

Manteniment

• Inspecció periòdica: Periodically inspect the chlorinator for any signs of wear, damage, or leaks. Check plumbing connections for integrity.
• Neteja: Clean the chlorinator chamber as needed to remove any residue or buildup from dissolved tablets. Always ensure the system is off, depressurized, and drained before cleaning. Rinse thoroughly with water.
• O-Ring Maintenance: Inspect the lid O-ring for cracks, tears, or deterioration. Apply a silicone-based lubricant to the O-ring periodically to keep it pliable and ensure a good seal. Replace the O-ring if it shows signs of wear.
• Hivernització: In climates where pools are winterized, ensure all water is drained from the chlorinator to prevent freezing and damage. Store the chlorinator in a dry, protected area if it is removed from the plumbing.

Resolució de problemes

Especificacions

Garantia i Suport

For specific warranty information regarding your Waterco Waterking Chlorinator Model 25500, please refer to the documentation included with your purchase or visit the official Waterco weblloc web. Conserveu el rebut de compra com a comprovant de compra per a reclamacions de garantia.

For technical support, troubleshooting assistance beyond this manual, or to inquire about replacement parts, please contact Waterco customer service directly. Contact details can typically be found on the manufacturer's weblloc web o a l'embalatge del producte.