1. Introducció
1.1 Producte acabatview
The Sensor Switch SPODM-2P-RD nLight SwitchPod Control is a 2-button, low voltage (12/24-Vdc) wall-mount switch designed for nLight lighting control systems. This device provides manual ON/OFF control for connected lighting or other loads within an nLight network.
1.2 Característiques clau
- nLight SwitchPod Switch
- Wall-Mount design
- 2-Button configuration (ON/OFF for two independent circuits or functions)
- Volum baixtage operation (12/24-Vdc)
- Acabat vermell
1.3 Contingut del paquet
- 1 x SPODM-2P-RD nLight SwitchPod Control
- Cargols de muntatge
- Guia d'instal·lació (aquest manual)
2. Informació de seguretat
Please read all instructions carefully before installation and operation. Failure to follow these instructions may result in property damage, injury, or death.
- ADVERTIMENT: To avoid fire, shock, or death, turn off power at the circuit breaker or fuse box and test that the power is off before wiring.
- This device is designed for low voltage (12/24-Vdc) applications only. Do not connect to line voltage (120V/240V AC).
- La instal·lació l'ha de dur a terme un electricista qualificat d'acord amb totes les normes elèctriques locals i nacionals.
- No instal·leu el producte si sembla que està danyat.
- No modifiqueu el dispositiu de cap manera.
3. Configuració i instal·lació
3.1 Eines necessàries
- Tornavís (Phillips i/o de punta plana)
- Pelafils
- Cinta elèctrica (opcional)
3.2 Instruccions de cablejat
The SPODM-2P-RD uses screw terminals for connection. Ensure all connections are secure.
Figura 3.2.1: lateral view of the SPODM-2P-RD with wiring label. This image shows the product's side profile, highlighting the label with detailed wiring instructions and specifications.
Figura 3.2.2: Esquena view of the SPODM-2P-RD. This image illustrates the rear of the switch, revealing the screw terminals where low voltage wires are connected for power and control signals.
- Apagueu l'alimentació: Before beginning any wiring, ensure power to the circuit is turned off at the circuit breaker. Verify with a voltage provador.
- Identificar els cables:
- WHT (White): Manual ON Input
- BLU (Blue) stripe: Right button output
- BLK (Black) stripe: Left button output
- RED (Red): Power (12/24-Vdc)
- YLW (Yellow): Comú
- Connecteu els cables: Connect the corresponding low voltage wires from your nLight system to the screw terminals on the SPODM-2P-RD. Ensure wires are stripped to the appropriate length and securely fastened under the screw terminals.
- Interruptor de muntatge: Carefully push the wired switch into the wall box. Secure it using the provided mounting screws.
- Instal·leu la placa de paret: Attach the decorative wallplate (not included) over the switch.
- Restaura l'alimentació: Torneu a encendre l'alimentació al disjuntor.
4. Funcionament
4.1 Funcionalitat bàsica
The SPODM-2P-RD features two independent push-buttons, each controlling an ON/OFF function within the nLight system. The control method is touch-based, responding to physical presses of the buttons.
Figura 4.1.1: Frontal view of the SPODM-2P-RD. This image displays the red faceplate with two sets of "ON" and "OFF" buttons, indicating its dual-channel control capability.
- Press the top "ON" button to activate the function associated with the upper control.
- Press the top "OFF" button to deactivate the function associated with the upper control.
- Press the bottom "ON" button to activate the function associated with the lower control.
- Press the bottom "OFF" button to deactivate the function associated with the lower control.
The specific actions triggered by these buttons are configured within the nLight system and may vary based on your installation.
5. Manteniment
The SPODM-2P-RD nLight SwitchPod Control requires minimal maintenance.
- Neteja: To clean the surface of the switch, use a soft, damp drap. No utilitzeu netejadors abrasius, dissolvents ni productes químics agressius, ja que poden danyar l'acabat o els components interns.
- Sense peces reparables per l'usuari: There are no user-serviceable parts inside this device. Do not attempt to open or repair the unit. Refer all servicing to qualified personnel.
6. Solució De Problemes
If you experience issues with your SPODM-2P-RD, refer to the following common troubleshooting steps:
| Problema | Causa possible | Solució |
|---|---|---|
| Switch does not respond. | Sense energia al dispositiu. Cablejat incorrecte. nLight system issue. | Verify power is supplied to the nLight system and the switch. Check wiring connections against the diagram in Section 3.2. Consult your nLight system's documentation or administrator. |
| Buttons feel loose or stuck. | Danys físics o deixalles. | Ensure no foreign objects are obstructing the buttons. If physically damaged, the unit may need replacement. |
| Incorrect function when button is pressed. | Incorrect nLight system configuration. | Verify the nLight system programming for the switch's address and button assignments. |
If the problem persists after attempting these solutions, contact Sensor Switch technical support or a qualified electrician.
7. Especificacions tècniques
| Atribut | Especificació |
|---|---|
| Número de model | SPODM-2P-RD |
| Marca | Interruptor del sensor |
| Mode d'operació | Automàtic |
| Vol. Operatiutage | 12/24 volts de corrent continu |
| Tipus de contacte | Normalment obert |
| Tipus de connector | Terminals de cargol |
| Tipus de circuit | 2 vies |
| Tipus d'actuador | Pulsador |
| Material de contacte | Metall |
| Classificació de protecció internacional | IP54 |
| Nombre de llocs | 2 |
| Mètode de control | Toca |
| Color | Vermell |
| Dimensions (L x A x A) | 4 x 2.5 x 1.75 polzades |
| Pes de l'article | 7.4 unces |
| Certificacions | CE, ETL, REACH, RoHS, WEEE, cULus |
8. Garantia i Suport
This product is covered by the manufacturer's standard warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Sensor Switch weblloc.
8.1 Suport tècnic
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact Sensor Switch customer support. Contact information can typically be found on the manufacturer's weblloc o embalatge del producte.
Nota: The input data does not provide specific contact details or warranty duration. Please refer to the manufacturer's official resources for the most accurate and up-to-date information.
