1. Introducció
This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your Behringer TD-3 Analog Bass Line Synthesizer. Please read this manual thoroughly to ensure proper use and to maximize the performance of your instrument.
The Behringer TD-3 is an analog bass line synthesizer designed to produce classic electronic music sounds. It features an all-analog signal path, a 16-step sequencer, and a resonant low-pass filter.
2. Configuració
2.1 Desembalatge
Carefully remove the TD-3 from its packaging. Retain the packaging materials for future transport or storage.
2.2 Connexió d'alimentació
Connect the included DC power adapter to the 'DC IN' port on the rear panel of the TD-3. Plug the adapter into a suitable power outlet. Ensure the power switch is in the 'OFF' position before connecting power.
2.3 Connexions d'àudio
- Sortida principal: Connect the 'OUTPUT' jack (1/4" TS) on the rear panel to your mixer, audio interface, or ampmés viu.
- Auriculars: Connect headphones to the 'PHONES' jack (1/4" TRS) on the front panel for private monitoring. Adjust the 'VOLUME' knob to a comfortable listening level.
2.4 MIDI/USB Connections
- Entrada/sortida MIDI: Use standard 5-pin DIN MIDI cables to connect the 'MIDI IN' and 'MIDI OUT' ports to other MIDI devices for synchronization or control.
- USB: Connect the USB port to a computer for MIDI control and firmware updates.
2.5 CV/Gate Connections
The TD-3 features 'CV OUT' and 'GATE OUT' jacks (3.5mm TS) for integration with modular synthesizers and other analog control voltage equipment. These outputs transmit pitch and gate information from the sequencer.
Imatge 1: Front panel and rear connections of the Behringer TD-3. This image displays the various knobs, buttons, and input/output jacks, including the power input, audio output, headphone jack, MIDI ports, USB port, and CV/Gate connections, all essential for setting up the device.
3. Operating the TD-3
3.1 Encès
After all connections are made, switch the 'POWER' button on the rear panel to the 'ON' position. The unit will power up.
3.2 Controlsview
The TD-3's front panel is divided into several sections:
- VCO (voltage Controlled Oscillator): Controls the basic sound waveform and pitch.
- VCF (voltage Controlled Filter): Shapes the timbre of the sound.
- Sobre: Controls the decay of the filter.
- Seqüenciador: Programs and plays musical patterns.
- Distorsió: Adds overdrive to the sound.
- Volum: Ajusta el nivell de sortida general.
3.3 VCO Section
- TUNE: Ajusta el to general de l'oscil·lador.
- FORMA D'ONA: Selects between Sawtooth (bright, rich harmonics) and Square (hollow, reedy) waveforms.
3.4 VCF Section
- TALLAR: Sets the frequency at which the filter begins to attenuate higher frequencies.
- RESONÀNCIA: Emphasizes frequencies around the cutoff point, creating a 'wah' effect at higher settings.
- SOBRE: Controls the amount of filter envelope modulation applied to the cutoff frequency.
- DECAÏMENT: Determines the length of the filter envelope's decay phase.
- ACCENT: Controls the intensity of the accent effect on notes.
3.5 Sequencer Operation
The TD-3 features a powerful 16-step sequencer for creating bass lines.
- Interruptor de MODE: Selects between 'WRITE' (for programming patterns) and 'PLAY' (for playing patterns or tracks).
- TRACK/PATTERN Selector: In 'PLAY' mode, choose between playing a single 'PATTERN' or a 'TRACK' (a chain of patterns). In 'WRITE' mode, select 'TRACK' to edit a track or 'PATTERN' to edit a pattern.
- PATTERN GROUP: Selects one of four groups (I, II, III, IV), each containing 8 patterns (1-8).
- TEMPS: Ajusta la velocitat de reproducció del seqüenciador.
- INICI / PARADA: Inicia o atura la reproducció del seqüenciador.
- ESCRIU/SEGÜENT: Used to confirm steps during pattern writing or to advance to the next step.
- MODE DE TO: Selects the input source for pitch information (INT for internal keyboard, MIDI, USB, TRIG for external trigger).
- MODE DE TEMPS: Sets the clock resolution for external synchronization (1PPS, 2PPQ, 24PPQ, 48PPQ).
- Botons de FUNCIÓ: These buttons (DEL, INS, CH, COPY, PASTE, TRANSPOSE, ACCENT, SLIDE) perform various editing functions within the sequencer.
- STEP Buttons (1-8, 9, 0, 100, 200): Used for entering notes, selecting steps, and other functions depending on the mode.
3.6 Distortion Section
- Interruptor ON / OFF: Engages or bypasses the built-in distortion effect.
- DISTORSIÓ: Ajusta la quantitat d'overdrive.
- TO: Shapes the frequency content of the distorted sound.
- NIVELL: Controls the output level of the distortion effect.
3.7 Control de volum
The 'VOLUME' knob adjusts the overall output level of the TD-3. Use this to balance the TD-3's output with other instruments in your setup.
4. Manteniment
4.1 Neteja
Clean the TD-3 with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the finish and internal components.
4.2 Emmagatzematge
When not in use, store the TD-3 in a cool, dry place away from direct sunlight and extreme temperatures. If transporting, use the original packaging or a suitable protective case.
4.3 actualitzacions de microprogramari
Revisa periòdicament el Behringer website for available firmware updates. Updates can provide new features, improvements, and bug fixes. Follow the instructions provided with the firmware update carefully.
5. Solució De Problemes
5.1 Sense sortida de so
- Ensure the power adapter is correctly connected and the unit is powered on.
- Comproveu la connexió i la integritat de tots els cables d'àudio.
- Verify the 'VOLUME' knob is turned up.
- If using headphones, ensure they are fully plugged in and the volume is adjusted.
- Confirm that a pattern is playing and the 'MODE' switch is set to 'PLAY'.
5.2 El seqüenciador no reprodueix
- Press the 'START/STOP' button to initiate playback.
- Ensure the 'MODE' switch is set to 'PLAY'.
- Check the 'TEMPO' knob setting; it might be set to a very slow speed.
- If synchronized externally, verify the external clock source is active and the 'TIME MODE' is correctly set.
5.3 MIDI Control Issues
- Ensure MIDI cables are connected correctly (MIDI OUT of controller to MIDI IN of TD-3).
- Verify that the TD-3 and your MIDI controller are on the same MIDI channel.
- Check the 'PITCH MODE' setting on the TD-3 to ensure it is set to 'MIDI' or 'USB' as appropriate.
6. Especificacions
| Característica | Especificació |
|---|---|
| Model | TD-3 |
| Tipus | Sintetitzador de baixos analògic |
| Dimensions (L x A x A) | 17.3 x 8.9 x 3.9 polzades (43.9 x 22.6 x 9.9 cm) |
| Pes | 2.8 lliures (1.27 kg) |
| Font d'alimentació | Adaptador de corrent continu (inclòs) |
| Sortida d'àudio | 1/4" TS, unbalanced |
| Sortida d'auriculars | 1/4" TRS, stereo |
| MIDI | MIDI In, MIDI Out (5-pin DIN) |
| USB | USB tipus B |
| CV/Gate Outputs | TS de 3.5 mm |
7. Garantia i Suport
Behringer products are designed and manufactured to high standards. For detailed warranty information and technical support, please refer to the official Behringer weblloc web o poseu-vos en contacte amb el vostre distribuïdor local. Conserveu el rebut de compra com a comprovant de compra per a reclamacions de garantia.
Per obtenir més ajuda, visiteu el Botiga Behringer a Amazon or the official Behringer support page.
