Manual d'usuari de l'interruptor de sensor de moviment TOPGREENER TDOS5-KM-I

1. Informació de seguretat

ADVERTIMENT: To avoid fire, shock, or death, turn off power at the circuit breaker or fuse box and test that power is off before wiring. Installation should be performed by a qualified electrician or a person with electrical experience. Read all instructions before installation.

• Do not use with electronic ballasts.
• Assegureu-vos el wat totaltage of connected lights does not exceed the switch's maximum rating.
• Només per a ús interior.

2. Producte acabatview

The TOPGREENER TDOS5-KM-I is a Passive Infrared (PIR) motion sensor switch designed to automatically control lighting based on occupancy or vacancy in a room. It features adjustable settings for motion detection sensitivity and time delay, offering flexible control for various applications.

Característiques principals:

• PIR Motion Detection with 180° field of view.
• Occupancy (Auto ON, Auto OFF) and Vacancy (Manual ON, Auto OFF) modes.
• No es requereix cap cable neutre.
• Operable without a ground wire connection (ground wire connection is recommended for safety).
• Compatible with dimmable LED light bulbs (minimum 15W load).
• Adjustable time delay (15 sec, 5 min, 10 min, 20 min, 30 min).
• Adjustable motion detection sensitivity (Range).

3. Instal·lació

3.1 Passos previs a la instal·lació

1. Apagueu l'alimentació: Locate the circuit breaker or fuse that supplies power to the switch location and turn it OFF. Verify power is off using a voltage provador.
2. Treure l'interruptor antic: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch.

3.2 Instruccions de cablejat

The TDOS5-KM-I features a universal wiring design, allowing for interchangeable hot and load wires, simplifying installation. A neutral wire is not required. While operable without a ground wire, connecting the ground wire is highly recommended for safety.

• Identificar els cables: In your wall box, identify the hot (line) wire and the load wire.
• Connecteu els cables: Connect the hot wire to one of the switch's terminals and the load wire to the other terminal. The switch's design allows these to be interchangeable.
• Ground Wire (Recommended): If a ground wire is present in your wall box, connect it to the green ground screw on the switch.
• Cables segurs: Assegureu-vos que totes les connexions dels cables estiguin segures.

3.3 Compatibility and Important Notes

• Aquest interruptor és ONLY compatible with dimmable LED light bulbs.
• Ho és INCOMPATIBLE with any lighting that includes electronic ballasts.
• The switch's circuit requires a minimum load of 15W.

3.4 Postinstal·lació

1. Interruptor de muntatge: Carefully push the wired switch into the wall box and secure it with screws.
2. Fixeu la placa de paret: Install the decorative wall plate.
3. Restaura l'alimentació: Torneu a encendre l'alimentació a l'interruptor.
4. Temps d’escalfament: Allow 1-2 minutes for the device to warm up after installation before testing its functionality.

4. Funcionament

The TDOS5-KM-I offers two operational modes: Occupancy and Vacancy, along with adjustable settings for motion detection range and time delay.

4.1 Modes de funcionament

• Occupancy Mode (Auto ON, Auto OFF): In this mode, the lights will automatically turn ON when motion is detected and turn OFF after a set time delay when no motion is detected.
• Vacancy Mode (Manual ON, Auto OFF): In this mode, the lights must be manually turned ON by pressing the switch button. They will then automatically turn OFF after a set time delay when no motion is detected.

4.2 Changing Modes

To switch between Occupancy and Vacancy modes, locate the ON/OFF push button on the face of the device. Press and hold this button for 3 seconds. The mode will toggle between Occupancy and Vacancy.

4.3 Configuracions ajustables

The switch features two adjustable dials located under the faceplate for customizing its performance:

• Interval: This dial controls the motion detection sensitivity. Adjust it according to the daylight conditions and the size of the room to optimize detection. Settings typically range from 1 (lowest sensitivity) to 4 (highest sensitivity).
• Hora: This dial determines how long the light will remain ON after the last detected motion. Available options include: 15 seconds (Test mode), 5 minutes, 10 minutes, 20 minutes, and 30 minutes.

5. Manteniment

The TOPGREENER TDOS5-KM-I Motion Sensor Switch requires minimal maintenance. To ensure optimal performance and longevity:

• Neteja: Periodically wipe the surface of the switch and sensor lens with a soft, dry cloth. Avoid using abrasive cleaners, solvents, or excessive moisture, as these can damage the device.
• Obstruccions: Ensure the sensor lens is not obstructed by furniture, decorations, or other objects that could block its field of view, affecting motion detection.

6. Solució De Problemes

If you experience issues with your TOPGREENER TDOS5-KM-I Motion Sensor Switch, refer to the following common problems and solutions:

7. Especificacions

• Model: TDOS5-KM-I
• Entrada Voltage: 120 VCA, 60 Hz
• Valoració actual: 1.25A
• Compatibilitat de càrrega: 300W Tungsten, 150W Dimmable LED
• Càrrega mínima: 15W
• Tipus de sensor: Infrarojos passius (PIR)
• Camp de View: 180 graus
• Àrea de cobertura màxima: 1200 metres quadrats
• Modes de funcionament: Occupancy (Auto ON/OFF), Vacancy (Manual ON/Auto OFF)
• Time Delay Options: 15 sec (Test), 5 min, 10 min, 20 min, 30 min
• Temperatura de funcionament: 32-104 °F (0-40 °C)
• Dimensions: 2.5" W x 4.5" H x 2.5" D (Device)
• Certificacions: UL Listed, Compliant with Title 20 & Title 24
• Cablejat: Single-pole only, no neutral wire required, operable without ground wire (ground recommended).

8. Garantia i Suport

For warranty information or technical support, please contact TOPGREENER customer service. Refer to the product packaging or the official TOPGREENER weblloc web per obtenir les dades de contacte i els termes de garantia més actualitzats.

Weblloc: www.topgreener.com