WOODS OEM 65587 Genuine Replacement Seal Kit User Manual

1. Introducció

This manual provides essential information for the proper installation and maintenance of the WOODS OEM 65587 Genuine Replacement Seal Kit. This kit is specifically designed to restore the hydraulic integrity of your 62290 Cylinder, ensuring optimal performance and longevity for your compatible BH650 and BH750 Backhoes.

Using genuine WOODS replacement parts is crucial for maintaining the original specifications and reliability of your equipment. This seal kit contains all necessary components to replace worn or damaged seals within the specified hydraulic cylinder.

Image 1.1: The complete WOODS OEM 65587 Genuine Replacement Seal Kit, showing various seals and components.

2. Instal·lació (Configuració)

Proper installation of the seal kit is critical for preventing leaks and ensuring the correct function of the hydraulic cylinder. It is recommended that this procedure be performed by a qualified technician or an individual with experience in hydraulic system repair.

2.1 Precaucions de seguretat

• Always relieve hydraulic pressure from the system before beginning any work on hydraulic components.
• Utilitzeu l'equip de protecció individual (EPI) adequat, incloent-hi ulleres i guants de seguretat.
• Ensure the equipment is stable and secured to prevent accidental movement.

2.2 Eines necessàries

Specific tools may vary depending on the cylinder design, but commonly include:

• Alicates per a anell de pressió
• Seal installation tools (plastic picks, seal drivers)
• Claus o preses
• Clean rags and hydraulic fluid

2.3 Passos d'instal·lació (generals)

1. Desmuntatge: Carefully disassemble the 62290 Cylinder according to the specific service manual for your BH650 or BH750 Backhoe. Note the orientation and position of all existing seals and components.
2. Neteja: Thoroughly clean all cylinder components, removing any old hydraulic fluid, dirt, or debris. Inspect cylinder bore, rod, and piston for any damage or scoring.
3. Seal Removal: Remove all old seals from the piston, rod, and gland. Dispose of old seals properly.
4. New Seal Installation: Lubricate new seals from the WOODS 65587 kit with clean hydraulic fluid before installation. Carefully install each seal into its correct groove, ensuring it is not twisted or pinched. Use appropriate seal installation tools to prevent damage.
5. Remuntatge: Reassemble the cylinder, ensuring all components are correctly aligned and torqued to specifications.
6. Sagnat del sistema: After reassembly, bleed the hydraulic system to remove any trapped air. Refer to your backhoe's service manual for the correct bleeding procedure.

Imatge 2.1: Una imatge detallada view of the various seals and rings included in the kit, ready for installation.

3. Post-Installation Verification

After installing the seal kit and reassembling the hydraulic cylinder, it is important to perform a thorough check to ensure proper functionality and detect any leaks.

3.1 Comprovació funcional

• Start the backhoe and allow the hydraulic system to warm up to operating temperature.
• Slowly cycle the affected hydraulic cylinder through its full range of motion several times. Observe for smooth operation and full extension/retraction.
• Listen for any unusual noises, which could indicate air in the system or improper assembly.

3.2 Leak Inspection

• Visually inspect all seal areas, connections, and hoses for any signs of hydraulic fluid leaks during and after cycling the cylinder.
• Pay close attention to the rod seal, piston seal (internal leakage may not be visible externally but will affect performance), and gland seals.
• Address any detected leaks immediately by re-tightening connections or re-evaluating the seal installation.

Image 3.1: A WOODS backhoe in operation, demonstrating the equipment context where the seal kit is used.

4. Manteniment

While the WOODS 65587 Seal Kit is designed for durability, regular maintenance of your hydraulic system will extend the life of the seals and the cylinder itself.

4.1 Consells generals de manteniment

• Inspecció periòdica: Periodically inspect hydraulic cylinders for external leaks, rod scoring, or unusual wear on seals.
• Qualitat del fluid: Ensure hydraulic fluid is clean and at the correct level. Contaminated fluid can accelerate seal wear. Follow manufacturer recommendations for fluid type and change intervals.
• Neteja: Keep the cylinder rod clean and free of dirt, mud, and debris, which can damage the rod seal as the cylinder cycles.
• Lubricació: Ensure all grease points on the backhoe, including cylinder pins, are regularly lubricated as per the equipment's maintenance schedule.

Image 4.1: Proper lubrication of moving parts is essential for overall equipment health and can indirectly protect hydraulic seals.

5. Solució De Problemes

If you encounter issues after installing the WOODS 65587 Seal Kit, consider the following common problems and solutions.

If troubleshooting steps do not resolve the issue, consult a certified hydraulic technician or contact WOODS customer support.

6. Especificacions

Key specifications for the WOODS OEM 65587 Genuine Replacement Seal Kit:

• Número de peça: 65587
• Compatible Cylinder: 62290 cilindre
• Compatible Backhoes: BH650, BH750
• Fabricant: WOODS
• Dimensions del producte: 7.5 x 3 x 1 polzades
• Pes de l'article: 1.92 unces
• ASIN: B0B22R58X7
• Data de primera disponibilitat: 23 de maig de 2022

6.1 Què hi ha a la caixa

• 1 x Seal Kit for 62290 Cylinder (WOODS OEM 65587)

Image 6.1: The official WOODS Genuine Parts logo, signifying authentic components.

7. Garantia i Suport

For information regarding warranty coverage for the WOODS OEM 65587 Genuine Replacement Seal Kit, please refer to the official WOODS website or contact WOODS customer support directly. Ensure you have your product details and purchase information available when contacting support.

WOODS Official Weblloc: www.woods.com