1. Introducció
This manual provides essential information for the proper installation and maintenance of your MTP Replacement Blade Locking Bolt. This component is designed as a direct replacement part for specific Dremel Saw Max and Ultra Saw models, ensuring secure blade attachment during operation.
Compatibilitat: This replacement blade locking bolt is compatible with the following Dremel models:
- Dremel Saw Max SM20
- Dremel Saw Max SM20-02
- Dremel Ultra Saw US40
Please consult your tool's original owner's manual to confirm the correct part number (2610016801) for your specific model before proceeding with installation.
2. Informació de seguretat
WARNING: Always disconnect the power tool from its power source before performing any assembly, adjustments, or maintenance. Failure to do so can result in serious personal injury.
- Durant la instal·lació, utilitzeu l'equip de protecció individual (EPI) adequat, com ara ulleres i guants de seguretat.
- Ensure the replacement part is clean and free from damage before installation.
- Do not overtighten the bolt, as this can damage the threads or the tool.
- Si no esteu segurs de cap pas, consulteu un tècnic qualificat o el manual de servei original de l'eina.
3. Contingut del paquet
El vostre paquet ha de contenir el següent element:
- 1 x MTP Replacement Blade Locking Bolt (Part Number: 2610016801)
4. Instal·lació
Follow these steps to replace the blade locking bolt:
- Desconnecteu l'alimentació: Ensure the Dremel tool is unplugged from the power outlet.
- Treure el cargol vell: Locate the existing blade locking bolt on your Dremel Saw Max or Ultra Saw. Use an appropriate tool (e.g., an Allen wrench or screwdriver, depending on the bolt head) to loosen and remove the old bolt.
- Remove Blade (if necessary): If the blade is still attached, carefully remove it after the old bolt is out.
- Zona d'inspecció: Clean any debris or dust from the blade mounting area and the bolt's threaded hole.
- Insert New Bolt: Place the new MTP Replacement Blade Locking Bolt into the designated threaded hole.
- Secure Blade (if necessary): If you removed the blade, re-insert it correctly, ensuring it is seated properly before tightening the bolt.
- Estreny el cargol: Hand-tighten the new bolt initially, then use the appropriate tool to tighten it securely. Do not overtighten. The bolt should hold the blade firmly in place without excessive force.
- Verifica la instal·lació: Gently attempt to move the blade by hand to ensure it is securely fastened and does not wobble.
- Eina de prova: Reconnect the tool to power and perform a brief, unloaded test run to ensure proper function before use.
Figure 1: MTP Replacement Blade Locking Bolt. This image shows the black, hexagonal head bolt with a threaded shaft, designed to secure a saw blade.
5. Funcionament
Once properly installed, the MTP Replacement Blade Locking Bolt functions identically to the original part, securing the cutting blade to your Dremel Saw Max or Ultra Saw. Ensure the bolt is always tightened correctly before operating the tool to prevent blade slippage or detachment, which could lead to injury or damage.
6. Manteniment
- Inspecció periòdica: Periodically inspect the blade locking bolt for any signs of wear, damage, or corrosion.
- Neteja: Keep the bolt and its threads clean from sawdust and debris. A small brush or compressed air can be used.
- Comprovació d'estanquitat: Before each use, verify that the blade locking bolt is securely tightened.
- Substitució: If the bolt shows signs of stripping, bending, or significant wear, replace it immediately to maintain tool safety and performance.
7. Solució De Problemes
| Problema | Causa possible | Solució |
|---|---|---|
| Blade is loose after tightening bolt. | Bolt not fully tightened, stripped threads on bolt or tool, incorrect blade seating. | Ensure bolt is tightened correctly. Inspect bolt and tool threads for damage; replace if stripped. Verify blade is seated properly. |
| Bolt cannot be removed or tightened. | Cross-threaded, seized due to corrosion, or damaged bolt head. | Apply penetrating oil if seized. Use correct tool for bolt head. If severely damaged, professional assistance may be required. |
| Bolt does not fit. | Incorrect part for your tool model. | Verify compatibility with your Dremel model (SM20, SM20-02, US40) and part number (2610016801). |
8. Especificacions
- Tipus de part: Blade Locking Bolt
- Marca: MTP
- Compatibilitat: Dremel Saw Max SM20, SM20-02, Dremel Ultra Saw US40
- OEM Part Number Equivalent: 2610016801
- Estil del cap: Hexagonal (Round head with hex drive)
- Material Grade: Grau 2
- ASIN: B0B2CCTVTJ
9. Garantia i Suport
For information regarding warranty coverage or technical support for your MTP Replacement Blade Locking Bolt, please contact the retailer or manufacturer directly. Keep your purchase receipt as proof of purchase.
For support related to your Dremel tool, please refer to the official Dremel documentation or contact Dremel customer service.
