1. Producte acabatview
This manual provides instructions for the KICKER 48TRTP122 12-inch CompRT Down-Firing Loaded Subwoofer Enclosure, the DS18 CANDY-X1B Mono Class D Amplifier, and the accompanying DS18 AMPKIT4 4AWG Complete Amplifier Wiring Kit. This system is designed to enhance your vehicle's audio experience with powerful bass output.
2. Què hi ha a la caixa
- Kicker 48TRTP122 12" CompRT Series Down-Firing Loaded Subwoofer Enclosure
- DS18 CANDY-X1B Mono Candy-X Series Car Ampmés viu
- DS18 AMPKIT4 4AWG Complete Amplifier Kit, including:
- 17 ft 4 AWG Red Power Wire
- 3 ft 4 AWG Black Ground Wire
- 17 ft Remote Wire
- 17 ft Red/Black Speaker Cable
- 17 ft Red/Black Twisted RCA Cable
- Mini ANL Fuse Holder with Mini ANL 100A Fuse
- 6 ft 4 AWG Loom Tube
- 1 x Rubber Grommet
- 10 x Brides de cable
- 2 x terminals d'anell
- 2 x terminals de pala
- 5 x Small Spade Terminals
Figure 2.1: Components of the DS18 AMPKIT4 4AWG Complete AmpKit lifier.
3. Configuració i instal·lació
La instal·lació correcta és crucial per a un rendiment i una seguretat òptims. Si no esteu segurs de cap dels passos a seguir, consulteu un instal·lador professional d'àudio per a cotxes.
3.1 Precaucions de seguretat
- Desconnecteu el terminal negatiu de la bateria del vehicle abans de començar qualsevol treball elèctric.
- Assegureu-vos que tot el cablejat estigui correctament aïllat i fixat per evitar curtcircuits i danys.
- Utilitzeu l'equip de protecció individual (EPI) adequat durant la instal·lació.
3.2 Subwoofer Enclosure Placement
The KICKER 48TRTP122 is a down-firing enclosure, designed to be placed in the trunk or cargo area of your vehicle. Ensure it is securely fastened to prevent movement during driving.
Figure 3.1: KICKER 48TRTP122 Down-Firing Subwoofer Enclosure.
3.3 AmpMuntatge de lifier
Mount the DS18 CANDY-X1B amplifier in a location that allows for adequate ventilation and protection from moisture. Common locations include under a seat, in the trunk, or on the back of a rear seat. Ensure it is securely mounted to prevent vibration damage.
Figure 3.2: DS18 CANDY-X1B Mono Class D Ampmés viu.
3.4 Instruccions de cablejat
Follow these steps carefully for wiring the system. Refer to the wiring diagram below for visual guidance.
- Power Wire (Red 4 AWG): Run the 17 ft red power wire from the vehicle's positive battery terminal to the fuse holder, then from the fuse holder to the +12V terminal on the DS18 amplifier. Ensure the fuse holder is installed close to the battery (within 18 inches).
- Ground Wire (Black 4 AWG): Connect the 3 ft black ground wire from the GND terminal on the ampel adaptador a una superfície metàl·lica neta i sense pintar del xassís del vehicle. Assegureu-vos d'una bona connexió elèctrica.
- Cable d'encesa remota: Connect the remote wire from your head unit's remote output to the REM terminal on the amplificador. Aquest cable fa que el ampengegueu i apagueu l'activador amb la unitat principal.
- Cables RCA: Connect the RCA cables from your head unit's subwoofer output (or full-range output if no dedicated sub output) to the RCA input jacks on the DS18 ampmés viu.
- Cable de l'altaveu: Connecteu el cable de l'altaveu del amplifier's speaker output terminals to the KICKER subwoofer enclosure's input terminals. Ensure correct polarity (+ to + and - to -). The KICKER 48TRTP122 enclosure has a 2-ohm impedance.
- Comandament de baix: Connect the included bass remote to the dedicated remote port on the DS18 amplifier. Mount the remote in an accessible location for easy adjustment.
Figure 3.3: Subwoofer to Amplifier Wiring Diagram (2-ohm connection).
Figure 3.4: DS18 Bass Remote Control.
4. Instruccions de funcionament
Once the system is installed, follow these steps to configure and operate your subwoofer and ampmés viu.
4.1 Engegada inicial i configuració del guany
- Torneu a connectar el terminal negatiu de la bateria del vehicle.
- Engegueu la unitat principal. El amplifier should power on (indicated by a blue LED on the ampmés viu).
- Estableix el amplifier's GAIN control to its minimum (fully counter-clockwise) position.
- Play a music track with strong bass at a moderate volume level on your head unit (around 75% of maximum volume).
- Slowly increase the GAIN control on the amplifier until you hear distortion, then back it off slightly until the sound is clear. This sets the maximum clean output level.
4.2 Amplifier Controls (DS18 CANDY-X1B)
The DS18 CANDY-X1B amplifier features several controls for fine-tuning your bass output:
- GUANY: Adjusts the input sensitivity to match the output of your head unit. (See 4.1)
- BASS BOOST (0-18 dB): Increases the bass output at a specific frequency (typically around 45 Hz). Use sparingly to avoid distortion and speaker damage.
- LPF (Low-Pass Filter) (50-150 Hz): This filter allows only frequencies below the set point to pass through to the subwoofer. Adjust to blend the subwoofer's output seamlessly with your main speakers.
- SUBSONIC FILTER (10-55 Hz): Filters out extremely low frequencies that are inaudible and can cause damage to the subwoofer. Set it slightly below your subwoofer's lowest usable frequency.
- PHASE (0/180 degrees): Adjusts the phase of the subwoofer output relative to your main speakers. Experiment with both settings to find the one that provides the most impactful and coherent bass.
- COMANDAMENT: Port for connecting the wired bass remote control, allowing convenient bass level adjustment from the driver's seat.
Figure 4.1: DS18 CANDY-X1B Amplifier Controls.
5. Manteniment
Un manteniment regular garanteix la longevitat i el rendiment òptim del vostre sistema d'àudio.
- Neteja: Keep the subwoofer enclosure and amplifier clean and free of dust and debris. Use a soft, dry cloth. Avoid liquid cleaners directly on components.
- Connexions: Comproveu periòdicament totes les connexions del cablejat per assegurar-vos que estiguin ben ajustades i que no estiguin corroses. Les connexions soltes poden provocar un rendiment deficient o danys.
- Ventilació: Assegureu-vos el amplifier's cooling fins are not obstructed to prevent overheating.
- Comprovació de fusibles: Si el amplifier does not power on, check the fuse in the fuse holder near the battery. Replace with a fuse of the same rating (100A Mini ANL).
6. Solució De Problemes
Consulteu aquesta secció per conèixer els problemes comuns i les seves solucions.
| Problema | Causa possible | Solució |
|---|---|---|
| No hi ha so del subwoofer |
|
|
| So distorsionat |
|
|
| Ampel lifier es sobreescalfa |
|
|
| Bass remote not working |
|
|
7. Especificacions
Detailed specifications for the components in this bundle.
7.1 KICKER 48TRTP122 12" CompRT Subwoofer Enclosure
- Tipus d'altaveu: Subwoofer
- Diàmetre del subwoofer: 12 polzades
- Potència màxima: 1000 watts
- Potència RMS: 500 watts
- Impedància: 2 ohms
- Sensibilitat: 98 dB
- Característica especial: Down-Firing, Active thin-mount CompRT subwoofer, High-output reFLEX passive woofer
- Material: Tauler de fibra de densitat mitjana
- Dimensions: 27.5" W x 6.125" H x 14.625" D (Top) x 14.625" D (Bottom)
7.2 DS18 CANDY-X1B Mono Class D Ampmés viu
- Potència RMS:
- 4 ohms: 240 watts x 1 channel
- 2 ohms: 400 watts x 1 channel
- 1 ohm: 600 watts x 1 channel
- Potència màxima de sortida: 1800 watts
- Sensibilitat: 100 dB
- Resposta de freqüència: 20-150 Hz
- Comandament de baix: Inclòs
- Disseny: Classe D
- Augment de baix variable: 0-18 dB
- Variable Low-pass filter (LPF): 50-150 Hz
- Filtre subsònic: 10-55 Hz
- Dimensions: 5.9" d'amplada x 8.3" de profunditat x 2.16" d'alçada
7.3 DS18 AMPKIT4 4AWG Complete AmpKit lifier
- Mesura de filferro: 4 AWG
- Material del filferro: High Performance CCA (Copper Clad Aluminum)
- Recomanat per a: Un amplifier up to 1300 Watts
- Components inclosos: Power wire, ground wire, remote wire, speaker cable, RCA cable, fuse holder with 100A fuse, loom tube, grommet, cable ties, various terminals.
8. Informació de la garantia
This product bundle typically comes with a manufacturer's warranty. The KICKER 48TRTP122 subwoofer enclosure and DS18 CANDY-X1B amplifier are covered by a full warranty from their respective manufacturers. Specific warranty terms, duration, and coverage details may vary. Please retain your proof of purchase for warranty claims.
For detailed warranty information, refer to the documentation included with each individual component or visit the respective manufacturer's official weblloc.
9. Suport
If you encounter issues not covered in this manual or require further assistance, please contact the manufacturer's customer support:
- KICKER Support: Visit the official KICKER weblloc web amb recursos de suport, preguntes freqüents i informació de contacte.
- DS18 Support: Visit the official DS18 website for product support and contact details.
When contacting support, please have your product model numbers (48TRTP122, CANDY-X1B, AMPKIT4) and proof of purchase readily available.