Introducció
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Brio Moderna Self-Cleaning Touchless Bottleless Water Cooler Dispenser. Please read this manual thoroughly before installation and use, and retain it for future reference.
The Brio Moderna dispenser offers advanced 3-stage filtration, personalized temperature adjustment for both cold and hot water, and a hygienic touchless dispensing system. It is designed to provide clean, refreshing water directly from your plumbed water line.
Informació important de seguretat
To reduce the risk of injury or property damage, observe the following safety precautions:
- Connecteu sempre el dispensador a una presa de corrent amb connexió a terra.
- No feu funcionar el dispensador si el cable d'alimentació està danyat.
- Ensure the dispenser is placed on a level, stable surface.
- Mantingueu el dispensador allunyat de la llum solar directa i de fonts de calor.
- No bloquejar les obertures de ventilació.
- Desendolleu el dispensador abans de netejar-lo o fer-ne cap manteniment.
- Aquest aparell no està pensat per ser utilitzat per persones (inclosos nens) amb capacitats físiques, sensorials o mentals reduïdes, o amb manca d'experiència i coneixements, tret que hagin rebut la supervisió o instruccions sobre l'ús de l'aparell per una persona responsable de la seva seguretat.
- Els nens han de ser supervisats per assegurar-se que no juguin amb l'aparell.
Components del producte
Your Brio Moderna water cooler dispenser comes with the following main components:
- Water Cooler Dispenser Unit (Black)
- 3-Stage Water Filter Kit (Sediment, Pre-Carbon, Post-Carbon Filters)
- Installation Kit (including necessary tubing and connectors for plumbed setup)
- Safata de goteig
- Cable d'alimentació
Image showing the Brio Moderna water cooler dispenser with its side panel open, revealing the filter compartments, alongside the boxed 3-stage filter replacement kit.
Configuració i instal·lació
1. Desembalatge i col·locació
- Traieu amb cura tots els materials d'embalatge.
- Place the dispenser on a flat, stable, and level surface. Ensure there is at least 4 inches of clearance from walls for proper ventilation.
- The dispenser is designed for indoor use only.
2. Instal·lació del filtre
- Open the filter compartment door, typically located on the lower front or side of the unit.
- Insert the Sediment, Pre-Carbon, and Post-Carbon filters into their respective slots. Ensure they are securely twisted or pushed into place according to the markings.
- Close the filter compartment door.
3. Water Line Connection (Plumbed Installation)
- Locate a cold water supply line near the dispenser's intended location.
- Tanqueu el subministrament d'aigua principal.
- Using the provided installation kit, connect the dispenser to the cold water supply line. Follow the specific instructions provided with the installation kit for proper connection to avoid leaks.
- Assegureu-vos que totes les connexions estiguin estretes i segures.
- Slowly turn on the main water supply and check for any leaks.
4. Neteja inicial
- Before first use, dispense several cups of water from both the cold and hot spouts to flush the system and filters. Discard this water.
- Continue flushing until the water runs clear and free of air bubbles.
5. Connexió d'alimentació
- Connecteu el dispensador a una presa de corrent amb connexió a terra.
- Allow approximately 15-30 minutes for the water to reach optimal cold and hot temperatures.
Instruccions de funcionament
Dispensing Water (Touchless Operation)
- Place your cup or container under the desired dispensing spout (cold or hot).
- Wave your hand approximately 1-2 inches in front of the motion sensor located above the dispensing area.
- Water will begin to dispense. Wave your hand again to stop the flow.
- Nota: The motion sensor feature is primarily designed for cold water dispensing. For hot water, a safety button or lever may need to be pressed in conjunction with the sensor or a manual button. Refer to the specific controls on your unit.
Ajust de temperatura
Your Brio Moderna dispenser allows for personalized temperature settings for both cold and hot water. Controls are typically located on the back or inside a panel of the unit.
- Temperatura de l'aigua freda: Use the cold water thermostat dial to adjust the temperature. Turning the dial towards 'colder' will decrease the temperature.
- Temperatura de l'aigua calenta: Use the hot water thermostat dial or button to adjust the temperature. Exercise caution when adjusting hot water settings.
Manteniment
Substitució del filtre
Els 3-stage filters should be replaced periodically to ensure optimal water quality. Filter life depends on water usage and local water quality, but generally, filters should be replaced every 6-12 months.
- Desendolleu el dispensador de la presa de corrent.
- Tanqueu el subministrament d'aigua al dispensador.
- Obriu el compartiment del filtre.
- Twist or pull out the old filters. Be prepared for a small amount of water to drip.
- Insert new Brio replacement filters, ensuring they are securely seated.
- Tanqueu el compartiment del filtre.
- Turn on the water supply and plug in the dispenser.
- Flush the new filters by dispensing several cups of water from both spouts.
Neteja del dispensador
- Neteja exterior: Netegeu les superfícies exteriors amb un damp tela. No utilitzeu netejadors abrasius ni dissolvents.
- Safata de degoteig: Regularly remove and empty the drip tray. Wash it with mild soap and water, then rinse and dry thoroughly before replacing.
- Funció d'auto-neteja: Your dispenser features a self-cleaning function. Refer to the specific instructions on your unit for activating this cycle. This typically involves pressing a dedicated button or sequence of buttons, which uses UV light or ozone to sanitize the water tanks.
Resolució de problemes
| Problema | Causa possible | Solució |
|---|---|---|
| No hi ha distribució d'aigua | Water supply off; clogged filter; airlock in system; dispenser unplugged. | Check water supply valve; replace filters; flush system; ensure dispenser is plugged in. |
| Water not cold/hot enough | Temperature setting too high/low; insufficient time to cool/heat; ventilation blocked. | Adjust temperature settings; allow more time; ensure proper ventilation around unit. |
| Fuites | Loose water line connection; damaged O-ring; cracked component. | Check all connections for tightness; inspect O-rings and components for damage. Contact support if leak persists. |
| Soroll inusual | Compressor cycling; air in system; loose component. | Normal operation may include compressor noise; flush system to remove air; check for loose parts. |
Especificacions
- Model: CLPOU720UVF3XB
- Marca: Brio
- Color: Negre
- Tipus d'instal·lació: Plumbed (Bottleless)
- Lloc d'accés: Bottom (for filter access)
- Filtració: 3-Stage (Sediment, Pre-Carbon, Post-Carbon)
- Dispensació: Touchless (Motion Sensor)
- Control de temperatura: Adjustable Cold & Hot
- Autoneteja: Sí
Garantia i Suport
For warranty information, product registration, or technical support, please refer to the warranty card included with your product or visit the official Brio website. You can also contact Brio customer service directly for assistance with troubleshooting or parts replacement.
Assistència en línia: Visita la botiga Brio a Amazon
