AeroCool Blade ATX Semi-Tower PC Case Instruction Manual

1. Introducció

The AeroCool Blade is an ATX semi-tower PC case designed for optimal airflow and aesthetic appeal. It features an RGB front panel with preset lighting modes, a full tempered glass side window, and ample space for component installation. This manual provides essential information for the proper setup, operation, and maintenance of your PC case.

Informació de seguretat: Always disconnect power from your system before performing any installation or maintenance. Handle components with care to avoid damage. Refer to individual component manuals for specific installation instructions.

2. Contingut del paquet

• AeroCool Blade ATX Semi-Tower PC Case
• 1 x 120mm RGB Rear Fan (pre-installed)
• 3 x 120mm Front Fans (pre-installed)
• Kit d'accessoris (cargols, separadors, brides per a cables)

3. Configuració i instal·lació

3.1 Preparació del cas

Carefully remove the case from its packaging. Place it on a stable, flat surface. Remove the tempered glass side panel by unscrewing the thumb screws at the rear of the case and gently pulling the panel away.

Figura 3.1: Intern view of the AeroCool Blade PC case, illustrating the layout for component installation.

3.2 Instal·lació de la placa base

1. Install the necessary motherboard standoffs into the motherboard tray according to your motherboard's form factor (ATX, Micro-ATX, Mini-ITX).
2. Instal·leu la protecció d'E/S a l'obertura posterior de la carcassa.
3. Col·loca amb cura la placa base sobre els separadors, alineant els forats dels cargols.
4. Fixeu la placa base amb els cargols proporcionats.

3.3 Instal·lació de la unitat d'alimentació (PSU).

The AeroCool Blade supports bottom-mounted PSUs. Slide your PSU into the dedicated compartment at the bottom rear of the case. Secure it with screws from the rear of the case.

3.4 Instal·lació de la unitat d'emmagatzematge

• Discs durs de 3.5 polzades: Install 3.5" hard drives into the drive cage located beneath the PSU shroud.
• SSD/HDD de 2.5": Install 2.5" drives onto the dedicated mounting points on the motherboard tray or behind it.

Figura 3.2: Part interna posterior view, highlighting cable management routes and 2.5-inch drive mounting locations.

3.5 Expansion Card (GPU) Installation

Remove the necessary expansion slot covers from the rear of the case. Insert your graphics card or other expansion cards into the PCIe slots on your motherboard and secure them with screws.

3.6 Fan and Cooling Installation

The case comes with one 120mm RGB fan pre-installed at the rear and three 120mm fans pre-installed at the front. Ensure all fan cables are connected to appropriate headers on your motherboard or fan controller.

Figure 3.3: A 120mm RGB fan, similar to those pre-installed in the AeroCool Blade case.

3.7 Connexions d'E/S del panell frontal

Connect the front panel cables (USB 3.0, USB 2.0, HD Audio, Power Switch, Reset Switch, LED Switch, Power LED, HDD LED) to the corresponding headers on your motherboard. Refer to your motherboard manual for exact pin configurations.

4. Instruccions de funcionament

4.1 Encès

Once all components are installed and connected, replace the side panel. Connect your monitor, keyboard, mouse, and power cable to the PSU. Press the Power button located on the top panel of the case to turn on your system.

Figura 4.1: Part superior frontal view of the case, indicating the location of the power button and front I/O ports.

4.2 Control d'il·luminació RGB

The AeroCool Blade features an RGB front panel. Use the dedicated LED button on the top panel to cycle through various preset lighting modes and effects. Pressing the button will change the lighting pattern or color.

Figura 4.2: Frontal view of the AeroCool Blade case with its distinctive RGB lighting.

4.3 Ports del panell frontal

The top panel provides convenient access to:

• 1 x port USB 3.0
• 2 x ports USB 2.0
• HD Audio output
• Entrada de micròfon

Connect your USB devices, headphones, and microphone to these ports as needed.

5. Manteniment

5.1 Neteja del filtre de pols

Regularly check and clean the dust filters to maintain optimal airflow and prevent dust buildup inside the case. Dust filters are typically located at the top, front, and bottom (under the PSU). Gently remove them and clean with compressed air or rinse with water (ensure they are completely dry before re-installation).

5.2 Neteja exterior

Netegeu les superfícies exteriors de la carcassa amb un drap suau iamp drap. Eviteu utilitzar productes químics agressius o materials abrasius que puguin danyar l'acabat o el vidre temperat.

6. Solució De Problemes

• El sistema no s'encén:
  Ensure the PSU is switched on and properly connected to the wall outlet. Verify all power cables from the PSU are correctly connected to the motherboard and components. Check the front panel power switch connection to the motherboard.
• La il·luminació RGB no funciona:
  Ensure the RGB controller (if applicable) and fan RGB cables are securely connected. Press the LED button on the top panel to cycle through modes. If connected to a motherboard header, check motherboard software settings.
• Els ventiladors no giren:
  Verify that all fan power cables are securely connected to the motherboard fan headers or a fan controller. Check BIOS/UEFI settings for fan speed control.
• L'USB/àudio del panell frontal no funciona:
  Ensure the USB and HD Audio cables from the front panel are correctly connected to the corresponding headers on your motherboard.

7. Especificacions

Figure 7.1: Dimensions of the AeroCool Blade PC Case.

8. Garantia i Suport

Per obtenir informació sobre la garantia i assistència tècnica, consulteu la pàgina oficial d'AeroCool. weblloc web o poseu-vos en contacte amb el vostre distribuïdor local. Conserveu el comprovant de compra per a reclamacions de garantia.

Informació de contacte: Per obtenir més ajuda, visiteu www.aerocool.io.