1. Producte acabatview
The IBO S-150 is an electronic control unit designed for managing the circulation pump in a central heating system. Its primary function is to activate the pump when the water temperature exceeds a preset value and deactivate it when the temperature falls below that value. This intelligent control helps to optimize energy consumption and extend the operational lifespan of the pump.
Característiques principals:
- Integrated Thermostat Function: Allows setting specific temperature thresholds for pump activation and deactivation.
- Funció anticongelant: Automatically activates the pump if the ambient temperature drops below 5 °C (41 °F) to prevent freezing within the system.
- Estalvi d'energia: Prevents unnecessary pump operation, leading to reduced energy consumption.
- Extended Pump Lifespan: Reduces wear and tear on the pump by operating it only when required.
- Indicadors LED: Two LED displays show current temperature and set stop temperature.
- Interfície fàcil d'utilitzar: Simple button controls for setting parameters.
2. Informació de seguretat
Llegiu atentament totes les instruccions de seguretat abans de la instal·lació i el funcionament. Si no seguiu aquestes instruccions, podeu patir descàrregues elèctriques, incendis o lesions greus.
- Seguretat elèctrica: Installation and maintenance should only be performed by qualified personnel in accordance with local electrical codes and regulations.
- Desconnexió d'alimentació: Always disconnect the power supply to the central heating system and the controller before performing any installation, wiring, or maintenance.
- Aigua i humitat: Do not expose the controller to water, excessive moisture, or extreme temperatures. Ensure the installation location is dry and protected.
- Connexió a terra adequada: Ensure the device is properly grounded to prevent electrical hazards.
- Integritat del cable: Regularly inspect all cables for damage. Do not use the device if any cables are frayed or damaged.
- Ús previst: Use the controller only for its intended purpose as a central heating pump controller.
3. Especificacions tècniques
| Paràmetre | Valor |
|---|---|
| Temperature Setting Range (Set Temperature) | De 0 °C a 99 °C (de 32 °F a 210 °F) |
| Temperature Setting Range (Stop Temperature) | De 0 °C a 99 °C (de 32 °F a 210 °F) |
| Temperatura ambient | -10 °C a 40 °C (de 14 °F a 104 °F) |
| Tipus de sensor de temperatura | Òhmic |
| Alimentació Voltage | 230 V, 50 Hz, ±10% |
| Power Consumption (Controller Only) | <5 W |
| Longitud del cable del sensor | Aproximadament 1 m (3.3 peus) |
| Longitud del cable d'alimentació | Aproximadament 1 m (3.3 peus) |
| Pump Power Cable Length | Aproximadament 1 m (3.3 peus) |
| Sortida | 230 V / 50 Hz |
| Maximum Load (Pump) | 6 A (Resistive Load) |
| Mesura de precisió | ~0.1 °C |
| Dimensions del producte (L x A x A) | 14 x 14 x 5 cm (5.5 x 5.5 x 2 polzades) |
| Pes | 370 grams (0.82 lliures) |
4. Instal·lació i configuració
Before proceeding with installation, ensure the main power supply to your central heating system is turned off at the circuit breaker.
4.1. Muntatge del controlador
Select a suitable, dry location for mounting the controller, away from direct heat sources or excessive moisture. The controller can be mounted on a wall using appropriate fasteners (not included). Ensure sufficient space for cable connections.
4.2. Connexió dels cables
The IBO S-150 controller comes with three main connections:
- Cable de corrent: This cable supplies power to the controller. Plug it into a standard 230V, 50Hz electrical outlet.
- Pump Power Cable: This cable connects the controller to your central heating circulation pump. Ensure the pump is compatible with the controller's specifications (Max load: 6A).
- Temperature Sensor Cable: The ohmic temperature sensor should be placed in a location where it can accurately measure the water temperature of the central heating system. Typically, this is on the return pipe or a designated sensor pocket. Ensure good thermal contact for accurate readings.
Figura 1: Mésview of the IBO S-150 controller with its connected power, pump, and sensor cables.
Figura 2: A baix view of the controller, illustrating the connection points for the power and pump cables.
After all connections are securely made, restore power to the central heating system.
5. Funcionament
The IBO S-150 controller features a simple interface with two LED displays and three control buttons.
Figure 3: Front panel of the IBO S-150 controller, showing the LED displays and control buttons.
5.1. Engegada inicial
Upon initial power-on, the upper LED display will show the current temperature measured by the sensor. The lower LED display will show the currently set 'stop temperature'.
5.2. Botons de control
- Botó MENÚ: Used to cycle through and select different settings (stop temperature, start temperature, anti-freeze function). Pressing this button allows you to enter the setting mode for each parameter.
- UP Arrow Button (▲): Used to increase the value of a selected parameter.
- DOWN Arrow Button (▼): Used to decrease the value of a selected parameter.
5.3. Setting Temperature Parameters
- Premeu el botó MENÚ button to enter the setting mode. The lower display will start flashing, indicating you can adjust the 'stop temperature'.
- Utilitza el Amunt (▲) i BAIX (▼) arrow buttons to set the desired temperature at which the pump should stop.
- Premeu el botó MENÚ button again to confirm the 'stop temperature' and move to the 'start temperature' setting. The lower display will flash again.
- Utilitza el Amunt (▲) i BAIX (▼) arrow buttons to set the desired temperature at which the pump should start. This is typically a few degrees higher than the stop temperature to prevent rapid cycling.
- Premeu el botó MENÚ button a third time to confirm the 'start temperature' and exit the setting mode. The controller will return to displaying the current and stop temperatures.
5.4. Funció anticongelant
The anti-freeze function is automatically engaged. If the temperature measured by the sensor drops below 5 °C (41 °F), the pump will activate regardless of other settings to circulate water and prevent freezing. This function cannot be manually disabled.
6. Manteniment
The IBO S-150 controller requires minimal maintenance to ensure optimal performance and longevity.
- Neteja: Periodically wipe the exterior of the controller with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the device.
- Inspecció del cable: Regularly check all connected cables (power, pump, sensor) for any signs of wear, damage, or loose connections. Replace damaged cables immediately.
- Col·locació del sensor: Ensure the temperature sensor remains securely in its intended position and maintains good thermal contact with the heating system pipe.
- Condicions ambientals: Verify that the controller's operating environment remains within the specified ambient temperature and humidity ranges.
7. Solució De Problemes
If you encounter issues with your IBO S-150 controller, refer to the following troubleshooting guide:
| Problema | Causa possible | Solució |
|---|---|---|
| El controlador no s'encén. | No power supply; loose power cable; faulty outlet. | Check power outlet; ensure power cable is securely plugged in; check circuit breaker. |
| Pump does not turn on when temperature is high. | Incorrect 'start temperature' setting; faulty pump connection; pump malfunction. | Verify 'start temperature' setting; check pump power cable connection; test pump independently if possible. |
| Pump does not turn off when temperature is low. | Incorrect 'stop temperature' setting; sensor malfunction. | Verify 'stop temperature' setting; check sensor connection and placement. |
| La lectura de temperatura és inexacta. | Sensor improperly placed; faulty sensor. | Ensure sensor has good thermal contact and is correctly positioned; replace sensor if necessary. |
| Anti-freeze function activates unexpectedly. | Ambient temperature near or below 5 °C; sensor reading error. | This is normal operation if ambient temperature is low. Check sensor reading for accuracy. |
If the problem persists after attempting these solutions, please contact a qualified technician or the product support.
8. Garantia i Suport
Per obtenir informació sobre la garantia i assistència tècnica, consulteu la documentació que s'inclou amb la compra o poseu-vos en contacte amb el vostre distribuïdor. Conserveu el comprovant de compra per a qualsevol reclamació de garantia.
Fabricant: IBO
Model Number: S-150