Manual d'usuari de la caixa JONSBO N2 NAS ITX

1. Introducció

This manual provides detailed instructions for the installation, operation, and maintenance of your JONSBO N2 NAS ITX Case. The JONSBO N2 is a compact aluminum chassis designed for Network Attached Storage (NAS) or mini PC builds, supporting up to five 3.5-inch hard disk drives and one 2.5-inch solid-state drive.

Image 1.1: JONSBO N2 NAS ITX Case with internal drive bays highlighted.

2. Configuració i instal·lació

Follow these steps to assemble your JONSBO N2 NAS ITX Case with your components.

2.1. Preparació

Before beginning, ensure you have the following components:

• Placa base ITX
• SFX Power Supply (maximum 150mm length)
• 3.5-inch Hard Disk Drives (up to 5)
• 2.5-inch Solid State Drive (1)
• Pro baixfile PCI Expansion Card (optional, maximum 197mm length)
• CPU Cooler (maximum 65mm height)
• Joc de tornavís
• Cable ties for management

2.2. Desmuntatge de la caixa

The JONSBO N2 features a removable top cover and a magnetic front panel for easy access.

1. Gently pull the magnetic front panel to detach it from the chassis.
2. Remove the screws securing the top cover and slide it off to expose the motherboard tray.

Image 2.1: Front panel removed, showing drive bays.

2.3. Motherboard and CPU Cooler Installation

1. Install your ITX motherboard onto the motherboard tray using the provided standoffs and screws.
2. Install your CPU cooler. Ensure its height does not exceed 65mm to allow the top cover to close properly.

2.4. Instal·lació de la font d'alimentació

1. Mount the SFX power supply into its designated bracket. The power supply should not exceed 150mm in length.
2. Fixeu la font d'alimentació amb cargols.

2.5. Instal·lació de la unitat

The JONSBO N2 supports five 3.5-inch hot-swappable HDDs and one 2.5-inch SSD.

1. 3.5-inch HDDs: Attach the provided handles and rubber slides to each 3.5-inch HDD. Slide each drive into an available hot-swappable bay until it clicks into place.
2. 2.5-inch SSD: Mount the 2.5-inch SSD in its dedicated slot, typically located behind the motherboard tray or within the drive cage structure.
3. Connect SATA data and power cables to all installed drives.

Imatge 2.2: Desplegada view illustrating component and drive installation.

2.6. Instal·lació de la targeta d'expansió

If using a low-profile PCI expansion card:

1. Remove the appropriate PCI slot cover from the rear of the case.
2. Inseriu el baix profile expansion card into the motherboard's PCI-E slot. The card length must not exceed 197mm.
3. Fixeu la targeta amb un cargol.

2.7. Front Panel and Cooling Connections

1. Connect the front panel headers (USB 3.2 Gen2 Type-C, USB 3.0, Audio+Mic, Power/Reset) to the corresponding pins on your motherboard.
2. Ensure the pre-installed rear 120mm fan is connected to a fan header on your motherboard for proper cooling.

2.8. Cable Management and Reassembly

1. Route all cables neatly to ensure optimal airflow and prevent interference with components. Use cable ties as needed.
2. Slide the top cover back into place and secure it with screws.
3. Reattach the magnetic front panel.

3. Instruccions de funcionament

3.1. Encendre/apagar

Press the power button located on the front panel to turn the system on or off. Follow your operating system's shutdown procedures for safe power-off.

3.2. Hot-Swapping Drives

The JONSBO N2 supports hot-swapping for its 3.5-inch HDD bays. Ensure your motherboard and operating system are configured to support hot-swapping before attempting this procedure.

1. Safely eject the drive from your operating system.
2. Gently pull the handle of the desired drive bay to release and remove the drive.
3. Insert a new 3.5-inch HDD into the empty bay, ensuring it slides in smoothly until it locks into place.
4. The operating system should detect the new drive.

4. Manteniment

Regular maintenance helps ensure the longevity and optimal performance of your JONSBO N2 case and its components.

4.1. Neteja

1. Exterior: Wipe the aluminum exterior with a soft, damp tela. Eviteu els netejadors abrasius.
2. Filtres de pols: The case includes dust filters. Periodically remove and clean them with water or compressed air. Ensure they are completely dry before reinstallation.
3. Components interns: Use compressed air to gently remove dust from internal components, especially the fan blades and heatsinks. Perform this with the system powered off and unplugged.

Image 4.1: Rear fan and filter assembly.

4.2. Ventilació

Ensure that all ventilation grilles on the case are unobstructed to maintain proper airflow and prevent overheating. Avoid placing the case in enclosed spaces without adequate air circulation.

Image 4.2: Product details including ventilation grille and rear fan.

5. Solució De Problemes

This section addresses common issues you might encounter with your JONSBO N2 case.

5.1. Sense poder

• Verify that the power supply is securely connected to the wall outlet and the motherboard.
• Check that the front panel power button header is correctly connected to the motherboard.
• Ensure the power supply unit (PSU) switch is in the 'ON' position.

5.2. Excessive Fan Noise

• Check if the fan blades are obstructed by cables or dust.
• Assegureu-vos que el ventilador estigui ben muntat i que no vibri contra la carcassa.
• If the stock 120x15mm fan is too loud, consider replacing it with a quieter aftermarket fan of the same dimensions.

5.3. Drive Not Detected

• Ensure all SATA data and power cables are securely connected to both the drives and the motherboard/PSU.
• For 3.5-inch HDDs, confirm they are fully seated in their hot-swappable bays.
• Check your motherboard's BIOS/UEFI settings to ensure SATA ports are enabled.

5.4. Sobreescalfament

• Verify that the rear 120mm fan is operating correctly.
• Improve cable management to reduce airflow obstruction.
• Ensure the case's ventilation grilles are clear of obstructions.

6. Especificacions

Detailed technical specifications for the JONSBO N2 NAS ITX Case:

Image 6.1: Chassis parameters and dimensions.

7. Garantia i Suport

JONSBO products are manufactured to high-quality standards. For specific warranty information regarding your JONSBO N2 NAS ITX Case, please refer to the warranty card included with your purchase or visit the official JONSBO weblloc.

If you encounter any issues or require technical assistance, please contact JONSBO customer support through their official channels. Provide your product model (N2) and a detailed description of the issue for efficient service.