LEDONE 8FT LED Vapor Tight Light Instruction Manual

1. Introducció

This manual provides detailed instructions for the safe installation, operation, and maintenance of your LEDONE 8FT LED Vapor Tight Light. Please read this manual thoroughly before installation and retain it for future reference. This fixture is designed for demanding environments requiring high resistance to water, dust, and corrosion, such as parking garages, car washes, cold storage, and industrial facilities.

2. Informació de seguretat

ADVERTÈNCIA: Risc de descàrrega elèctrica. Desconnecteu l'alimentació abans de la instal·lació o el manteniment.

• Installation must be performed by a qualified electrician in accordance with the National Electrical Code (NEC) and local codes.
• Assegureu-vos el subministrament voltage is compatible with the fixture's requirements (120-277Vac).
• Do not handle energized fixtures with wet hands or while standing on wet or damp superfícies.
• No intenteu modificar ni desmuntar l'aparell. No hi ha peces a l'interior que l'usuari pugui reparar.
• Utilitzeu l'equip de protecció individual (EPI) adequat durant la instal·lació.
• Assegureu-vos que el dispositiu estigui ben fixat per evitar que caigui.

3. Contingut del paquet

Verifiqueu que tots els components siguin presents i no estiguin danyats abans de continuar amb la instal·lació.

• LEDONE 8FT LED Vapor Tight Light Fixture
• Mounting Hardware (clips, screws, anchors)
• Manual d'instruccions (aquest document)

4. Configuració i instal·lació

4.1. Preinstal·lació

1. Apagueu l'alimentació: Locate the circuit breaker or fuse box and turn off the power supply to the installation area. Verify power is off using a voltage provador.
2. Desembalar: Carefully remove the fixture from its packaging. Inspect for any shipping damage.
3. Seleccioneu Wattage and Color Temperature (CCT): Before mounting, adjust the wattage and CCT switches located on the fixture. These switches allow you to select between 60W, 80W, or 100W and 3500K, 4000K, or 5000K. Make your selection based on your lighting requirements.

Image: Product dimensions and location of wattage/CCT selection switches.

4.2. Muntatge del dispositiu

The fixture is designed for surface mounting. Use the provided mounting clips and hardware.

1. Mark the desired mounting locations on the ceiling or wall. Ensure the marks are level and spaced appropriately for the fixture's length.
2. Perforeu forats pilot als llocs marcats. Introduïu ancoratges de paret si el munteu en plaques de guix o maçoneria.
3. Fixeu els clips de muntatge a la superfície amb els cargols proporcionats.
4. Snap the LED vapor tight fixture into the mounted clips, ensuring it is firmly seated.

Imatge: Example of surface mounting in a facility.

Image: Detail of the linkable design feature.

4.3. Cablejat elèctric

This fixture supports 0-10V dimming. Follow the wiring diagram below and local electrical codes.

• Connecteu el Negre cable des del dispositiu fins al Línia (L) cable de la font d'alimentació.
• Connecteu el Blanc cable des del dispositiu fins al Neutre (N) cable de la font d'alimentació.
• Connecteu el Verd cable des del dispositiu fins al Terra (GND) cable de la font d'alimentació.
• For 0-10V dimming: Connect the Lila cable des del dispositiu fins al Dim+ wire from the 0-10V dimmer. Connect the Rosa/Gris cable des del dispositiu fins al Dim wire from the 0-10V dimmer.
• Ensure all connections are secure using appropriate wire connectors.

Note: If 0-10V dimming is not used, cap the purple and pink/gray wires individually with wire nuts.

5. Instruccions de funcionament

1. Encès: Once installation and wiring are complete, restore power to the circuit at the breaker or fuse box. The fixture should illuminate.
2. Dimecres: If connected to a compatible 0-10V dimmer, adjust the dimmer control to achieve the desired light output level.
3. Wattage and CCT Adjustment: Wattage and CCT are set via internal switches during installation. These are not typically adjusted during normal operation. If changes are needed, disconnect power before accessing the switches.

6. Manteniment

The LEDONE Vapor Tight Light is designed for long-term, low-maintenance operation. Regular cleaning can help maintain optimal light output.

• Neteja: Desconnecteu l'alimentació abans de netejar. Feu servir un drap suau i sec.amp cloth with a mild, non-abrasive cleaner to wipe the exterior of the fixture. Do not use harsh chemicals or abrasive pads, as these can damage the finish or lens.
• Inspecció: Periodically inspect the fixture and mounting hardware for any signs of damage, loose connections, or wear. Address any issues promptly.
• Sense peces reparables per l'usuari: The LED light source and driver are integrated components. Do not attempt to open or repair the fixture. Contact qualified personnel for any issues beyond basic cleaning and inspection.

Image: The IP65 waterproof rating ensures durability in wet conditions.

7. Solució De Problemes

Before performing any troubleshooting, ensure power is disconnected at the circuit breaker.

8. Especificacions

Image: Key features and certifications of the LEDONE Vapor Tight Light.

9. Informació de la garantia

LEDONE products are manufactured to high quality standards. This product comes with a standard manufacturer's warranty. Please refer to the product packaging or the official LEDONE website for specific warranty terms and conditions. Keep your proof of purchase for warranty claims.

10. Atenció al client

If you have any questions, require technical assistance, or need to report an issue, please contact LEDONE customer support:

• Weblloc: Visit the LEDONE Store on Amazon (per a consultes generals)
• Correu electrònic: Consulteu l'embalatge del producte o la informació oficial website for direct support email.
• Telèfon: Consulteu l'embalatge del producte o la informació oficial website for direct support phone number.

Please have your product model number (8FT LED Vapor Tight Light) and proof of purchase ready when contacting support.