Introducció
The BENINCA to.GO2WV is a 2-channel, 433.92 MHz rolling code transmitter designed for use with compatible BENINCA gate and garage door openers. This remote control combines a modern design with robust functionality, offering a reliable solution for controlling two distinct automation systems. It is an evolved remote control concept, replacing older models like the T2WV, and is also available with sequential code for multiple code storage.
Contingut del paquet
- 2 x BENINCA to.GO2WV Remote Controls
- Piles (preinstal·lades o incloses per separat)
- Manual d'instruccions (aquest document)
Producte acabatview
Image: The BENINCA to.GO2WV remote control. This black, ergonomic remote features two distinct light grey buttons on its face, designed for controlling two separate channels. The "to.GO" branding is subtly embossed on the lower left side of the remote's body.
The to.GO2WV remote is designed for ease of use with its ergonomic shape and two clearly defined buttons. Each button corresponds to a channel, allowing control of two different automation systems. The rolling code technology ensures enhanced security for your gate or garage door.
Configuració i Programació
To ensure proper operation, the to.GO2WV remote must be programmed to your BENINCA receiver. The programming procedure typically involves accessing the receiver unit and initiating a pairing sequence. Refer to your specific BENINCA receiver's manual for detailed programming instructions, as procedures may vary slightly between models.
General Programming Steps (Consult Receiver Manual for Specifics):
- Accés al receptor: Locate your BENINCA gate or garage door opener's receiver unit. This may require opening the control panel.
- Activa el mode de programació: Press and hold the programming button (often labeled "PROG," "MEMO," or similar) on the receiver until an indicator light (LED) changes state or a specific sound is heard.
- Transmit Code from New Remote: While the receiver is in programming mode, press and hold the desired button on your new to.GO2WV remote for a few seconds.
- Confirmeu l'aparellament: The receiver's indicator light should confirm successful pairing (e.g., flash rapidly, turn solid, or turn off). Release the button on the remote.
- Prova de funcionament: After programming, test the remote's functionality from a safe distance to ensure it operates the gate or garage door correctly.
- Program Second Channel (if applicable): Repeat the process for the second button if you wish to control another device.
Note: If you are replacing an existing BENINCA remote, some receivers may support a "remote-to-remote" cloning procedure. Consult your receiver's manual for this advanced option.
Funcionament del comandament a distància
Once programmed, operating the BENINCA to.GO2WV remote is straightforward:
- Obertura/tancament: Press the programmed button corresponding to the gate or garage door you wish to operate. A single press typically initiates the open or close cycle.
- Parada: Pressing the button again during an open or close cycle may stop the movement, depending on your receiver's configuration.
- Interval: Ensure you are within the operational range of your receiver. Obstructions and environmental factors can affect signal strength.
Manteniment
The BENINCA to.GO2WV remote is designed for durability, but proper care will extend its lifespan:
- Neteja: Wipe the remote with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
- Substitució de la bateria: When the remote's range decreases significantly or the indicator light (if present) fails to illuminate, it's time to replace the battery. The to.GO2WV typically uses a standard coin cell battery (e.g., CR2032). To replace, carefully open the remote's casing (often by prying gently along the seam with a small flat-head screwdriver) and replace the battery, observing polarity.
- Emmagatzematge: Guardeu el comandament a distància en un lloc sec, allunyat de temperatures extremes i de la llum solar directa.
- Evitar l'impacte: Do not drop the remote or subject it to strong impacts.
Resolució de problemes
If you encounter issues with your BENINCA to.GO2WV remote, refer to the table below for common problems and solutions:
| Problema | Causa possible | Solució |
|---|---|---|
| Remote not working / No response |
|
|
| Reduït rang de funcionament |
|
|
| El comandament a distància funciona de manera intermitent |
|
|
If these solutions do not resolve the issue, please contact customer support or a qualified technician.
Especificacions
| Característica | Detall |
|---|---|
| Model | to.GO2WV |
| Freqüència | 433.92 MHz |
| Tipus de codificació | Rolling Code |
| Canals | 2 |
| Dispositius compatibles | BENINCA Receivers |
| Característica especial | Disseny ergonòmic |
| Font d'alimentació | Battery (e.g., CR2032 coin cell) |
Compatibilitat
The BENINCA to.GO2WV remote control is 100% compatible with the following BENINCA remote models and systems:
- TO.GO 4WV
- T2WV
- T4WV
- CUPIDO-2
- CUPIDO-4
- BENINCA IO.2WV (all colors)
It is designed to work seamlessly with BENINCA gate and garage door opener receivers operating on the 433.92 MHz rolling code frequency.
Informació de la garantia
For specific warranty terms and conditions, please refer to the warranty documentation provided with your purchase or contact the original seller. Warranty coverage typically addresses manufacturing defects and material flaws under normal use.
Atenció al client
If you have any questions regarding the setup, operation, or troubleshooting of your BENINCA to.GO2WV remote control, please contact the seller or the BENINCA customer support directly. Provide your product model number and a detailed description of your issue for efficient assistance.
We are fully committed to 100% customer satisfaction.
