Introducció
The Klein Tools 935DAF Digital Angle Finder is designed for precise measurements of inside and outside angles, lengths, and for calculating miter saw angles. It provides an accuracy of +/-0.2 degrees, assisting in achieving precise miter joints. Its compact design and clear display make it suitable for various professional and DIY applications.
Característiques clau
- Funcionalitat versàtil 3 en 1: Measures inside and outside angles, lengths, and calculates miter saw cut angles.
- Miter Saw Protractor: Facilitates calculation of optimal saw blade angles for accurate miter joints.
- Machined Ruler Edges: Ensures accurate measurements with a precision of +/- 0.2 degrees.
- Pantalla LED brillant: White LED display offers clear visibility in various lighting conditions.
- Construcció duradora: Features a rust-resistant metallic ruler with deeply etched markings for longevity and clear readings.
- Disseny compacte: Easy to store and carry, powered by a single AAA battery (included).
Configuració
1. Instal·lació de la bateria
The Klein Tools 935DAF requires one AAA battery, which is included. To install or replace the battery:
- Localitzeu la tapa del compartiment de la bateria a la part posterior de la unitat de visualització digital.
- Obriu la tapa.
- Inseriu una pila AAA, assegurant-vos de la polaritat correcta (+/-).
- Tanqueu bé la tapa del compartiment de la bateria.
Image: The digital angle finder highlighting its bright LED display, wide locking knob, and indicating it is powered by a single AAA battery.
2. Powering On/Off and Zeroing
- Encès/apagat: Manteniu premut el botó d'encesa (⏻) for approximately 2 seconds to turn the device on or off.
- Reinicialització del zero: A short press of the power button (⏻) will reset the angle measurement to zero. Ensure the rulers are in the desired starting position before zeroing.
Instruccions de funcionament
1. Measuring Angles
The digital angle finder can measure both inside and outside angles up to 360 degrees.
- Loosen the locking knob to allow the rulers to move freely.
- Position the rulers against the surfaces of the angle you wish to measure.
- Once positioned, tighten the locking knob to secure the angle.
- Read the angle measurement directly from the digital LED display.
Image: The digital angle finder positioned to measure a 90-degree angle on a wooden structure, displaying "90.0" on its screen.
Image: A user wearing work gloves uses the digital angle finder to measure and mark an angle on a piece of wood with a yellow pencil.
2. Miter Saw Angle Calculation
The 935DAF can assist in setting miter saw angles for precise cuts.
- Measure the desired angle of your joint using the angle finder.
- Premeu el botó MTR DEG button. The display will show the calculated miter saw setting.
- Adjust your miter saw to this displayed angle for accurate miter cuts.
Image: The digital angle finder displaying "45.0" degrees, with the "MTR DEG" button visible, indicating its use for miter saw angle calculations.
3. Holding a Measurement
To hold the current measurement on the display, press the MANTENIM botó. Premeu-lo de nou per deixar-lo anar i reprendre el mesurament en directe.
Manteniment
Neteja
Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the display or metallic surfaces.
Canvi de bateria
Replace the AAA battery when the display becomes dim or the device fails to power on. Refer to the "Battery Installation" section under Setup for instructions.
Emmagatzematge
Store the angle finder in a dry environment. Its compact design allows for easy storage in toolboxes or pockets.
Image: The digital angle finder being placed into a side pocket of a Klein Tools backpack, demonstrating its compact and portable design for easy storage.
Resolució de problemes
- El dispositiu no s'encén:
- Ensure the AAA battery is correctly installed with proper polarity.
- Substituïu la bateria per una de nova.
- Confirm the power button is pressed and held for approximately 2 seconds.
- Lectures inexactes:
- Ensure the rulers are clean and free from debris that might obstruct proper contact with surfaces.
- Perform a zero reset by briefly pressing the power button when the rulers are closed or at a known zero position.
- Verify the locking knob is tightened to prevent movement during measurement.
- La pantalla és tènue o parpelleja:
- Substituïu la bateria AAA.
Especificacions
| Fabricant | Eines Klein |
| Número de part | 935DAF |
| Pes de l'article | 6.9 unces |
| Dimensions del producte | 8.55 x 1.38 x 0.74 polzades |
| Número de model de l'article | 935DAF |
| Bateries | Necessita 1 bateria AAA (inclosa) |
| Material | Plàstic ABS, acer inoxidable |
| Font d'alimentació | Funciona amb bateria |
| Components inclosos | Cercador d'angles digital |
| Tipus de pila de bateria | Alcalí |
Informació de la garantia
For detailed warranty information, please refer to the attached warranty document provided with your product packaging. This document outlines the terms and conditions of the manufacturer's warranty.
Suport
For further assistance, technical support, or to inquire about replacement parts, please visit the official Klein Tools weblloc web o poseu-vos en contacte amb el seu departament d'atenció al client. Podeu trobar més informació i productes a Botiga d'eines Klein a Amazon.
