Introducció
Welcome and thank you for choosing the Baseus UltraControl Go Series Car Holder. This manual provides instructions for proper installation, operation, and maintenance of your device. Please read it carefully before use to ensure optimal performance and safety.
Producte acabatview
Components del producte
The Baseus UltraControl Go Series Car Holder consists of the following main components:
- Telèfon Clamp: Subjecta el teu telèfon intel·ligent de manera segura.
- Braç ajustable: Allows for positioning the phone at various angles.
- Base de ventosa: Provides secure attachment to surfaces.
- Botó d'alliberament: For easy one-hand operation to release the clamp braços.
Imatge: Frontal view of the Baseus UltraControl Go Series Car Holder, showing the phone clamp, adjustable arm, and suction cup base.
Configuració i instal·lació
Selecció d'una ubicació d'instal·lació
The Baseus UltraControl Go Series Car Holder can be installed on various smooth, flat surfaces within your vehicle, such as the dashboard or windshield. Ensure the chosen location does not obstruct your view o interferir amb els controls del vehicle.
Imatge: Examples of suitable installation locations for the car holder, including the dashboard, passenger seat area, and windshield.
Attaching the Suction Cup Base
- Clean the desired surface thoroughly to remove dust and grease.
- Place the suction cup base firmly onto the clean surface.
- Press down on the locking lever (if present) on the suction cup to create a vacuum seal.
Nota: The suction cup features removable nano adhesive for enhanced grip. Ensure the surface is suitable for adhesive application if using this feature.
Instruccions de funcionament
Inserting Your Phone
- Gently pull open the clamping arms of the holder.
- Place your smartphone into the holder, ensuring it rests securely on the bottom support.
- Allibera el clamping arms. The damped design will automatically adjust to securely grip your phone.
The holder is compatible with phones ranging from 5.4 to 7.2 inches.
Image: A smartphone held securely by the clamping arms of the car holder, illustrating the tight grip.
Removing Your Phone (Single-Hand Operation)
To remove your phone, press the release button located on the back of the holder's panel. The clamp arms will open, allowing you to easily retrieve your device.
Image: A hand pressing the release button on the back of the phone holder, demonstrating the single-hand operation for phone removal.
Ajustant el Viewangle ing
The adjustable arm and ball joint allow for flexible positioning. Loosen the adjustment knob (if present) to change the angle, then tighten it to secure the desired position.
Cura i Manteniment
- Neteja: Netegeu el suport amb un drap suauamp drap. Eviteu productes de neteja o dissolvents abrasius.
- Ventosa: If the suction cup loses adhesion, rinse it with warm water and let it air dry. This can restore its stickiness.
- Temperatura: Avoid prolonged exposure to extreme temperatures, which can affect the material and adhesive properties.
- Coixinets de silicona: The protective silicone pads on the clamping arms should be kept clean to maintain grip and prevent scratches to your phone.
Image: Illustration highlighting the meticulous craftsmanship and meshing gears designed to prevent squeaking during driving, indicating durability and quality.
Resolució de problemes
| Problema | Causa possible | Solució |
|---|---|---|
| Holder does not stick to surface. | Surface is dirty, uneven, or suction cup is not properly sealed. | Clean the surface. Ensure the suction cup lever is locked. Rinse and air dry the suction cup. |
| Phone is not held securely. | Phone size is outside the compatible range (5.4-7.2 inches) or clamping arms are obstructed. | Verify phone size. Ensure no obstructions prevent the arms from closing fully. |
| Holder makes noise during driving. | Loose connection or component. | Check all adjustable parts and ensure they are tightened. The design is intended to prevent squeaking. |
Especificacions del producte
- Número de model: BS-CM025 (C40361600111-00)
- Marca: Baseus
- Applicable Phone Size: 5.4 - 7.2 polzades
- Material: Silicone (for protective pads)
- Tipus de muntatge: Vehicle Mount (Suction Cup)
- Característiques especials: Adjustable, Secure Clamping, Wide Compatibility, Secure Installation, Protective Silicone Pads, Single-Hand Operation
- Dimensions del producte: 18 x 0.5 x 10 cm
- Pes de l'article: 120 g
- Color: Negre
Image: Diagram highlighting key features such as damping clamp arms, vacuum suction cup, removable nano adhesive, and easy operation.
Garantia i assistència al client
For warranty information or technical support, please refer to the official Baseus weblloc web o poseu-vos en contacte amb el vostre distribuïdor local. Conserveu el rebut de compra per a reclamacions de garantia.
Fabricant: Baseus
Weblloc: www.baseus.com
Contacte: Consulteu el weblloc web amb informació de contacte regional.
