1. Introducció
The FLIPSKY 75200 Pro V2.0 is an advanced electronic speed controller (ESC) designed for high-performance electric vehicles such as skateboards, scooters, and ebikes. It features an aluminum PCB for enhanced heat dissipation and an integrated power button for convenient operation. This manual provides essential information for setup, operation, and maintenance of your FLIPSKY 75200 Pro V2.0 ESC.
Figure 1: FLIPSKY 75200 Pro V2.0 Electronic Speed Controller.
2. Característiques del producte
- Firmware: Version 6.02, with support for future firmware updates.
- Voltage Rang: 14-84V (4-20S battery configurations).
- Capacitat actual: 100A continuous, with burst capabilities (values depend on mounting, ambient temperature, and air circulation).
- BEC: 5V@1.5A output.
- Motor Control Modes: Supports BLDC square wave mode and FOC sine wave mode.
- ERPM: Fins a 150,000.
- Interfícies de comunicació: USB, CAN, UART.
- Sensors compatibles: ABI, HALL, AS5047, AS5048A.
- Input Set Support: PPM, ADC, NRF, UART.
- Mida del cable: 10AWG for main power wires.
- Programable: Yes, via VESC_TOOL.
- Capacitat regenerativa: Sí.
- Phase Filter: Included for stable operation.
- Botó d'interruptor d'alimentació: Integrated red power switch button.
- Integrated Bluetooth Module: Allows convenient connection to Bluetooth parameters and real-time data reading without external modules.
- Proteccions avançades: Inclou baix volumtage, alt voltage, over current, temperature, MOSFET, and motor over-temperature protection.
- Modes de control: Supports Current / Duty cycle / Speed / PID control modes.
- IMU Module Support: Compatible with IMU modules like MPU9250, MPU6050, LSM6DS3, BMI160 via IIC interface for balancing car functions.
- CPU: 32F405 with 168MHz frequency.
- Dissipació de calor: Aluminum PCB and aluminum case design provide good heat dissipation for extended lifespan.
3. Especificacions
| Especificació | Valor |
|---|---|
| Firmware | 6.02 (firmware update supported) |
| Voltage Rang | 14-84 V (4-20S) |
| Corrent continu | 100A |
| Sortida BEC | 5 V @ 1.5 A |
| ERPM | 150,000 |
| Control Interface Ports | USB, CAN, UART |
| Sensors compatibles | ABI, HALL, AS5047, AS5048A |
| Input Set Support | PPM, ADC, NRF, UART |
| Mida del cable | 10 AWG |
| Dimensions (L x A x A) | 130 mm x 67.7 mm x 39.4 mm |
| Material | Alumini |
| Color | Negre |
Figura 2: Dimensions del producte.
Figure 3: Internal PCB dimensions.
4. Configuració
Proper connection of the FLIPSKY 75200 Pro V2.0 is crucial for safe and optimal performance. Refer to the diagram below for connection points.
Figure 4: Connection Diagram.
4.1. Connexions d'alimentació
- Bateria: Connect your battery pack to the main red (+) and black (-) terminals. Ensure correct polarity. The ESC supports 4-20S battery configurations.
- Motor: Connect the three phase wires (blue, green, yellow) from your motor to the corresponding terminals on the ESC.
- Interruptor d'alimentació: Connect the integrated power switch to the designated port.
4.2. Sensor and Communication Connections
- Sensor Hall: If your motor has Hall sensors, connect the Hall sensor cable to the HALL port on the ESC. Ensure the pinout matches.
- PPM (Pulse Position Modulation): For throttle input from a remote receiver, connect the PPM signal wire to the PPM port.
- CAN (Controller Area Network): Use the CAN bus for communication between multiple ESCs (e.g., in a dual motor setup) or other CAN-enabled devices.
- USB: Connect the ESC to a computer via the USB port for configuration and firmware updates using the VESC_TOOL software.
- UART (Universal Asynchronous Receiver-Transmitter): For serial communication with external modules like Bluetooth modules (though this ESC has integrated Bluetooth) or other accessories.
- COM: This port provides additional communication lines for various sensors or peripherals.
4.3. Initial Configuration (VESC_TOOL)
After physical connections, the ESC requires configuration using the VESC_TOOL software. This software allows you to set motor parameters, battery limits, control modes, and perform motor detection. It is highly recommended to follow the official VESC_TOOL documentation for detailed configuration steps to prevent damage to the ESC or motor.
- Download the latest VESC_TOOL from the official VESC project weblloc.
- Connect the ESC to your computer via USB.
- Launch VESC_TOOL and perform motor detection.
- Configure battery voltage limits, current limits, and other safety parameters according to your setup.
- Utilize the integrated Bluetooth module to connect to the VESC_TOOL mobile application for real-time data monitoring and parameter adjustments.
Video 1: Demonstration of the 75200 Pro V2.0 ESC features and operation.
5. Instruccions de funcionament
Once properly configured, the FLIPSKY 75200 Pro V2.0 ESC is ready for operation. The ESC supports various control modes to suit different applications and user preferences.
5.1. Encès / apagat
- Press the integrated red power button to turn the ESC on or off.
- Assegureu-vos que totes les connexions estiguin ben fixades abans d'encendre.
5.2. Modes de control
The ESC can be configured for the following control modes via VESC_TOOL:
- Control actual: Motor current is directly controlled by the input signal.
- Duty Cycle Control: Voltage is controlled as a percentage of the battery voltage.
- Speed Control (RPM): The ESC attempts to maintain a target motor RPM.
- Control PID: Advanced control loop for precise speed or position control, often used with IMU modules for balancing applications.
5.3. Regenerative Braking
The ESC supports regenerative braking, which converts kinetic energy back into electrical energy to recharge the battery during braking. Ensure that regenerative current limits are set appropriately in VESC_TOOL to avoid overcharging your battery.
Video 2: Short demonstration of the FLIPSKY 75100/75200 series ESC.
6. Manteniment
Regular maintenance helps ensure the longevity and reliable performance of your FLIPSKY 75200 Pro V2.0 ESC.
- Mantenir net: Periodically clean the exterior of the ESC to prevent dust and debris buildup, especially on the heatsink fins. Use a soft, dry cloth.
- Comproveu les connexions: Regularly inspect all wire connections (battery, motor, sensors, communication) for looseness, corrosion, or damage. Secure any loose connections.
- Monitorització de la temperatura: While the ESC has built-in temperature protection, it is good practice to monitor its temperature during heavy use, especially in enclosed spaces. Ensure adequate airflow around the unit.
- Actualitzacions de firmware: Check for official firmware updates periodically using VESC_TOOL. Updates can provide performance improvements, bug fixes, and new features.
- Emmagatzematge: When not in use for extended periods, store the ESC in a dry, cool environment away from direct sunlight and extreme temperatures.
Figura 5: A baix view highlighting the heatsink for good heat dissipation.
7. Solució De Problemes
If you encounter issues with your FLIPSKY 75200 Pro V2.0 ESC, consider the following troubleshooting steps:
| Problema | Causa possible | Solució |
|---|---|---|
| L'ESC no s'encén. | Loose battery connection, faulty power button, dead battery. | Comproveu el volum de la bateriatage and connections. Ensure the power button is correctly connected and functioning. |
| Motor not spinning or erratic behavior. | Incorrect motor phase wire connection, incorrect Hall sensor connection, improper VESC_TOOL configuration. | Verify motor and Hall sensor wiring. Re-run motor detection in VESC_TOOL. Check motor and battery current limits. |
| ESC overheating. | Insufficient airflow, excessive current draw, incorrect motor parameters. | Ensure proper ventilation. Reduce load or adjust current limits in VESC_TOOL. Check motor resistance and inductance values. |
| Problemes de connexió Bluetooth. | Interference, incorrect pairing procedure, outdated VESC_TOOL app. | Ensure no strong interference sources. Follow the pairing instructions for the VESC_TOOL app. Update the app to the latest version. |
For more detailed diagnostics and advanced troubleshooting, refer to the comprehensive documentation available for VESC-based ESCs and the FLIPSKY support resources.
Vídeo 3: Acabatview of the VESC 75200 Pro.
8. Garantia i Suport
8.1. Informació de la garantia
The FLIPSKY 75200 Pro V2.0 ESC comes with a 2 mesos de garantia des de la data de compra. Aquesta garantia cobreix els defectes de fabricació en condicions d'ús normals. Si us plau, conserveu el comprovant de compra per a reclamacions de garantia.
8.2. Atenció al client
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact FLIPSKY customer support through their official website or the retailer from whom you purchased the product. Provide your product model, serial number (if applicable), and a detailed description of the issue to expedite support.
