Yealink VCR11 Controller User Manual

1. Introducció

This manual provides detailed instructions for the setup, operation, and maintenance of your Yealink VCR11 Controller. The VCR11 is designed to seamlessly integrate with Yealink Meetingbar A10, A20, and A30 devices, offering intuitive control over your conferencing experience.

2. Producte acabatview

The Yealink VCR11 is a dedicated remote controller for Yealink Meetingbar systems. It features a comprehensive button layout for easy navigation, call management, and system settings adjustment.

Image 1: The Yealink VCR11 Controller, a silver-colored remote with a numeric keypad and dedicated function buttons for meeting control.

3. Configuració

3.1. Instal·lació de la bateria

The VCR11 Controller requires two AAA batteries (not included). To install:

1. Obriu la tapa del compartiment de la bateria a la part posterior del comandament a distància.
2. Introduïu dues piles AAA, assegurant-vos de la polaritat correcta (+/-).
3. Tanqueu bé la tapa del compartiment de la bateria.

3.2. Pairing with Yealink Meetingbar

To use the VCR11 Controller, it must be paired with your Yealink Meetingbar A10, A20, or A30. Follow these general steps:

1. Ensure your Meetingbar is powered on and connected to a display.
2. On the Meetingbar's interface (via touch screen or existing remote), navigate to Settings > Bluetooth > Pair New Device (o un camí similar).
3. On the VCR11 Controller, press and hold the OK botó i el Casa button simultaneously for approximately 3-5 seconds until an indicator light on the remote begins to flash, indicating pairing mode.
4. On the Meetingbar's display, select the VCR11 from the list of available Bluetooth devices.
5. Once paired, the indicator light on the VCR11 will stop flashing and remain solid for a few seconds, then turn off. The Meetingbar display will confirm successful pairing.

Note: Specific pairing steps may vary slightly depending on your Meetingbar's firmware version. Refer to your Meetingbar's user manual for precise instructions if needed.

4. Funcionament del controlador

The VCR11 Controller provides intuitive access to various functions of your Yealink Meetingbar. Below is a description of the main buttons:

• Botó d'engegada (⏻): Press to power on or off the Meetingbar. A short press may put the device into standby mode, while a long press typically powers it off completely.
• Navigation Pad (Up, Down, Left, Right): Used to navigate through menus and options on the Meetingbar's display.
• Botó D'acord: Confirms selections or enters sub-menus.
• Botó d'inici (⌂): Returns to the main home screen of the Meetingbar interface.
• Botó enrere (↩): Torna a la pantalla o al menú anterior.
• Botons de pujar / baixar de volum (+ / -): Adjusts the audio volume of the Meetingbar.
• Botó de silenci (🔇): Mutes or unmutes the microphone.
• Call/Answer Button (☎): Initiates a call or answers an incoming call.
• Hang Up/End Call Button (☎): Ends an active call or declines an incoming call.
• Zoom In/Out Buttons (🔍): Controls the digital zoom of the Meetingbar's camera.
• Numeric Keypad (0-9, *, #): Used for dialing numbers, entering PINs, or other numerical inputs.

5. Manteniment

5.1. Substitució de la bateria

When the remote's functionality becomes inconsistent or unresponsive, it is likely time to replace the batteries. Follow the battery installation steps in Section 3.1.

5.2. Neteja

To clean the VCR11 Controller, use a soft, dry, lint-free cloth. For stubborn marks, slightly dampen the cloth with water. Avoid using harsh chemicals, abrasive cleaners, or solvents, as these can damage the remote's surface or internal components.

6. Solució De Problemes

• El comandament a distància no respon:
  • Comproveu i substituïu les piles.
  • Ensure there are no obstructions between the remote and the Meetingbar.
  • Verify the remote is within the operational range of the Meetingbar.
• Error de vinculació:
  • Repeat the pairing process as described in Section 3.2.
  • Assegureu-vos que no hi hagi altres dispositius Bluetooth que interfereixin amb el procés d'emparellament.
  • Restart both the Meetingbar and the VCR11 Controller, then attempt pairing again.
• Buttons not working correctly:
  • Clean the remote to ensure no debris is obstructing the buttons.
  • If specific buttons are consistently unresponsive, contact customer support.

7. Especificacions

8. Garantia i Suport

For warranty information and technical support, please refer to the documentation included with your Yealink Meetingbar or visit the official Yealink website. You may also contact your reseller for assistance.