Introducció
The ANENG GN601 Wood Moisture Meter is a portable, pin-type detector designed for accurate and rapid measurement of moisture levels in various materials, including wood, concrete, bricks, and other building materials. Its compact design and versatile features make it suitable for woodworking, water damage restoration, construction, and home improvement projects.
Què s'inclou
- 1X ANENG GN601 Lumber Moisture Meter
- 2X 1.5V AAA Batteries
- 1X Manual d'usuari
Figure 1: Contents of the ANENG GN601 package, showing the moisture meter, batteries, and protective cap.
Configuració
Instal·lació de la bateria
- Localitzeu el compartiment de la bateria a la part posterior del dispositiu.
- Feu servir un tornavís per obrir la tapa del compartiment de la bateria.
- Insert two 1.5V AAA batteries, ensuring correct polarity.
- Substituïu la tapa del compartiment de la bateria i fixeu-la amb el cargol.
Video 1: Demonstrates the battery installation process for the ANENG GN601 moisture meter. The video shows disassembling the back cover, inserting two AAA batteries, and re-securing the cover.
Instruccions de funcionament
Funcions clau
- Botó d'encesa: Encén/apaga el dispositiu.
- Material Selection Key (Mode): Cycles through different material types for accurate readings.
- Botó de retroil·luminació: Activates/deactivates the LCD backlight for visibility in low-light conditions.
- Data Retention (Hold): Congela la lectura actual a la pantalla.
Figura 2: Detallada view of the ANENG GN601, highlighting the high-precision pins and the clear LCD display.
Calibració manual
Before each use, it is recommended to perform a self-calibration to ensure accuracy:
- Enceneu el dispositiu.
- Remove the protective cap from the pins.
- Insert the pins into the test point located on the protective cap.
- The display should show approximately 20.5% RH, indicating the meter is normal and calibrated.
Material Selection and Measurement
The ANENG GN601 features 7 calibration scales for different materials. Press the 'Mode' button to cycle through these options:
- Mode 1: Beech, Spruce, Larch, Walnut (8.8% - 54.8%)
- Mode 2: Oak, Maple, Lauan (6.8% - 47.9%)
- Mode 3: Concrete, Cement sand bed (0.9% - 22.1%)
- Mode 4: Gypsum mortar layer (0.0% - 11.0%)
- Mode 5: Cement mortar (0.7% - 8.6%)
- Mode 6: Lime mortar, Gypsum (0.0% - 16.5%)
- Mode 7: Brick (0.0% - 16.5%)
To measure, firmly press the pins into the material. The moisture percentage es mostrarà a la pantalla LCD.
Figure 3: Measuring moisture content in wood using the ANENG GN601.
Figure 4: Measuring moisture content in a wall using the ANENG GN601.
Detecció de temperatura i humitat
The device can also measure ambient temperature and humidity. These readings are displayed alongside the moisture content.
Especificacions
| Característica | Detall |
|---|---|
| Fabricant | ANENG |
| Número de part | GN601 |
| Pes de l'article | 5.6 unces |
| Dimensions del paquet | 5.79 x 2.8 x 1.34 polzades |
| Número de model de l'article | Multimeter-type Moisture Meter |
| Font d'alimentació | Funciona amb bateria |
| Piles incloses? | Sí |
| Necessites piles? | Sí |
| Tipus de pila de bateria | Alcalí |
| Gamma d’humitat | 0.0% to 58% (material dependent) |
| Apagat automàtic | Després de 10 minuts d'inactivitat |
| Mostra | Pantalla LCD amb retroiluminació |
Manteniment
- Mantingueu el dispositiu net i sec. Netegeu-lo amb un drap suau i sec.amp cloth; do not use abrasive cleaners or solvents.
- Guardeu el mesurador en un lloc fresc i sec, allunyat de la llum solar directa i de temperatures extremes.
- Always replace the protective cap over the pins when not in use to prevent damage and ensure safety.
- Si no heu d'utilitzar el dispositiu durant un període prolongat, traieu-ne les piles per evitar fuites i danys.
Resolució de problemes
| Problema | Causa possible | Solució |
|---|---|---|
| El dispositiu no s’encén. | Piles baixes o gastades; instal·lació incorrecta de la bateria. | Canvieu les piles; assegureu-vos de la polaritat correcta. |
| Lectures inexactes. | Pins not fully inserted; incorrect material mode selected; calibration needed. | Ensure pins are fully inserted; select correct material mode; perform manual calibration. |
| La pantalla està tènue o parpelleja. | Bateria baixa. | Substituïu les piles. |
| "LO" or "HI" reading. | Moisture content is outside the measurable range for the selected material. | This indicates the material is either extremely dry (LO) or extremely wet (HI) beyond the meter's range for that specific material type. |
Garantia i Suport
ANENG provides a lifetime of service and technical support for the GN601 Wood Moisture Meter. For any inquiries, technical assistance, or warranty claims, please contact ANENG customer support through the official channels provided with your product or visit the ANENG store online.
Visita el ANENG Store per a més informació.
