BN-LINK U135BL 7-Day Programmable Astronomical Timer Switch Instruction Manual

Introducció

Thank you for choosing the BN-LINK U135BL 7-Day Programmable Astronomical Timer Switch. This device is designed to automate your lighting based on astronomical events like sunrise and sunset, offering convenience and energy efficiency. Please read this manual thoroughly before installation and operation to ensure proper use and safety.

Informació de seguretat

• Cable neutre necessari: A neutral wire is essential for the installation of this timer switch.
• Single Pole Only: This timer switch is designed for single-pole installations only.
• Llistat per ETL: This product is ETL listed, ensuring compliance with North American safety standards.
• Electricista qualificat: Always have a qualified electrician install this product to prevent electrical hazards.
• Power Off at Breaker: Before any installation or maintenance, always cut off power at the circuit breaker to avoid electric shock.

Configuració i instal·lació

1. Desempaquetatge i preparació

The package includes the BN-LINK U135BL timer switch, a wall plate, mounting screws, and twist-on wire connectors. You will need a flat-head screwdriver and a Phillips head screwdriver for installation.

2. Instruccions de cablejat

Important: Ensure power is OFF at the circuit breaker before proceeding.

1. Unscrew and remove the existing wall plate and switch.
2. Verify the presence of a neutral wire in your wall box. A neutral wire is typically white.
3. Connecteu el filferro negre of the timer to the hot wire of the wall box using a twist-on wire connector.
4. Connecteu el fil vermell of the timer to the cable de càrrega of the wall box using a twist-on wire connector.
5. Connecteu el fil blanc of the timer to the fil neutre of the wall box using a twist-on wire connector.
6. Connecteu el fil verd of the timer to the cable de terra of the wall box using a twist-on wire connector.
7. Carefully push the wired timer switch into the wall box and secure it with the provided screws.
8. Col·loqueu la placa de paret.

3. Initial Power-On and System Reset

1. Turn power back ON at the circuit breaker.
2. If the screen is blank, dim, or flashing, allow the internal battery to charge for 10 minuts.
3. Press the "RESET" button to reset the system. The screen display will flash.
4. Hold the "SET" button for 3 segons to quit the flashing clock display.

Nota: The system time and all settings will be erased after a system reset.

4. Setting Current Date, Time, and Sunrise/Sunset Time

Follow these steps to configure the basic time settings:

1. Any de configuració: Press "SET". The year (e.g., 2018) will flash. Use "+" or "-" to set the current year (from 2018 to 2099).
2. Set Month and Day: Press "SET" again to confirm the year. The month and day will flash. Use "+" or "-" to set the current date (from 1.1 to 12.31).
3. Set Hour and Minute: Press "SET" again to confirm the date. The hour and minute will flash. Use "+" or "-" to set the current time (from 12:00 AM to 11:59 PM). Ensure you select the correct AM/PM format.
4. Confirm Time and DST: Press "SET" to confirm the correct time. Then use "+" or "-" to set DST (Daylight Saving Time) to ON or OFF. Enable DST if your region observes it to avoid manual adjustments.
5. Trieu la zona horària: Press "SET" to confirm DST setting. The Time Zone will flash. Use "+" or "-" to choose your local time zone from PAC (Pacific), MOU (Mountain), CEN (Central), EAS (Eastern), HAW (Hawaii), and ALA (Alaska).
6. Set Sunrise/Sunset Time: Press "SET" to confirm the current time zone. The sunrise time will flash. Use "+" or "-" to set the correct sunrise time for your time zone. Press "SET" again, and the sunset time will flash. Use "+" or "-" to set the correct sunset time.
7. Sortir de la configuració: Press "SET" to confirm the sunset time and exit the setting process. If you are in Daylight Saving Time, check if the DST icon is displayed.

Consell: If you want to quit setting at any stage, hold "SET" for 3 seconds or leave the buttons untouched for 90 seconds. Pressing "+" or "-" once changes values by one unit. Holding for less than 2 seconds changes by 6-8 units/second. Holding for 2 seconds or more changes by 60 units/second.

Instruccions de funcionament

1. Setting ON and OFF Events (Programs)

The timer switch supports up to 18 ON/OFF programs. To set a program:

1. Press "PROG". The display will show "--:--".
2. Press "SET" to set the first ON event. The day of the week will flash first. Use "+" or "-" to choose the desired day(s) or day combination (e.g., MO TU WE TH FR SA SU, MO, TU, WE, TH, FR, SA, SU, MO TU WE TH FR, SA SU).
3. Press "SET" to confirm the day(s). The time will flash. Use "+" or "-" to set the desired ON time (from 12:00 AM to 11:59 PM). If you want to choose sunrise or sunset time as the ON time, press the 'D/D' button once for sunrise or twice for sunset.
4. Press "PROG" to confirm the ON event. The display will show "--:--" again.
5. Press "SET" to set the first OFF event. The day of the week will flash first. Use "+" or "-" to choose the desired day(s) or day combination.
6. Press "SET" to confirm the day(s). The time will flash. Use "+" or "-" to set the desired OFF time (from 12:00 AM to 11:59 PM). If you want to choose sunrise or sunset time as the OFF time, press the 'D/D' button once for sunrise or twice for sunset.
7. Press "PROG" to confirm the OFF event. The display will show "--:--" again.
8. Repeat steps 2.2 to 2.6 to set additional programs, up to a maximum of 18.

Consell: To quit event setting at any stage, hold "PROG" for 3 seconds or leave the keys untouched for 90 seconds. To clear or resume the current input, press either the ON/OFF key once or twice. To revise a previous input, press 'SET' to shift to the relevant stage and make the correction.

2. Mode automàtic/manual

This timer switch has two operating modes: MANUAL (MAN ON/MAN OFF) and AUTO (AUTO ON/AUTO OFF).

• Canvi de modes: After completing program setup, press and hold the ON/OFF button for 3 seconds or longer to switch between MANUAL and AUTO modes.
• Mode MANUAL: Press ON/OFF to turn the timer constantly ON or OFF.
  • MAN ON: la sortida de potència està constantment activada.
  • MAN OFF: la sortida de potència està constantment OFF.
• Mode AUTOMÀTIC: Press ON/OFF to temporarily turn the timer ON or OFF.
  • AUTO OFF: Power output is temporarily cut off and will be resumed upon the next ON event.
  • AUTO ON: Power output is temporarily active and will be cut off upon the next OFF event.

Nota: Ensure the timer switch is set to AUTO mode for it to operate based on the programmed settings.

3. Daylight Savings Time (DST) Mode

The DST mode automatically adjusts the time, eliminating the need for manual changes and ensuring accurate lighting control year-round.

• Activate/Deactivate DST: Temporarily activate or deactivate DST by holding the "+" button for 3 seconds.
• When DST is ON, the DST icon will be displayed on the screen.
• When DST is OFF, the icon will disappear.

4. Mode aleatori

Activate the "Random" vacation mode to randomize light schedules, creating the illusion that your home is occupied to deter potential intruders.

• Activate/Deactivate Random Function: Press and hold "-" for 3 seconds or more to activate or deactivate the random function.
• When this function is active, the "RND" icon will display.
• At least one program must be set before activating the random function.
• When the random function is active, the ON and OFF events will be randomly postponed by 0-30 minutes respectively.

Manteniment

The BN-LINK U135BL timer switch requires minimal maintenance. Ensure the device is kept clean and free from dust. Do not use abrasive cleaners or solvents. In case of any issues, refer to the troubleshooting section or contact customer support.

Resolució de problemes

Problem 1: No screen display or faded display.

Possible causa: Bateria baixa.

Acció correctiva: Energize the timer to charge the internal battery for 10 minutes, then press the "RESET" button to reset the timer.

Problem 2: Timer does not turn on or off as programmed.

Possible Cause A: El temporitzador funciona en mode manual.

Acció correctiva: Switch the operation mode to AUTO by holding the ON/OFF button for 3 seconds.

Possible Cause B: Random function is active.

Acció correctiva: Deactivate random function by holding the "-" button for 3 seconds.

Possible Cause C: DST is disabled, while the device is located in a region that observes DST. As a result, the internal time was not adjusted when DST started or ended, causing the scheduled operations to run at incorrect times.

Acció correctiva: Enable DST by following the time setting procedure on the timer switch (hold "+" for 3 seconds).

Possible Cause D: Current system time on the timer switch is incorrect.

Acció correctiva: Verify and correct the current time setting on the device by following the time setting procedure on the timer switch.

Possible Cause E: Els programes no estaven configurats correctament.

Acció correctiva: Re-program the timer following the operating instructions in this manual.

Especificacions

Informació de la garantia

BN-LINK products are designed to provide reliable performance. For specific warranty details, please refer to the documentation included with your purchase or contact BN-LINK customer support. Keep your purchase receipt as proof of purchase for warranty claims.

Atenció al client

If you require further assistance or have any questions regarding your BN-LINK U135BL Astronomical Timer Switch, please contact our support team:

• Correu electrònic: support@bn-link.com
• Weblloc: Visit the BN-LINK Store on Amazon

Estem aquí per ajudar!