Manual d'usuari del kit de desenvolupament M5Stack NanoC6

1. Introducció

The M5Stack NanoC6 is a miniature, low-power IoT development board designed for a wide range of applications. It integrates an ESP32-C6FH4 microcontroller, offering advanced wireless communication capabilities including Wi-Fi 6, Zigbee, Thread, and Matter protocols. This compact device also features a built-in infrared emitter for controlling IR-enabled IoT devices and programmable RGB LEDs for visual feedback. The onboard ceramic antenna ensures reliable wireless connectivity, and the Grove interface provides flexible expansion options for various M5 devices.

2. Producte acabatview

2.1 Característiques clau

• Supports 2.4GHz Wi-Fi 6 (802.11ax), Zigbee, Thread, and Matter wireless protocols.
• Equipped with a built-in infrared LED for remote control applications.
• Features programmable RGB LEDs for visual indicators.
• Includes a Grove port for easy expansion with M5Stack modules.
• Integrated ceramic antenna for stable wireless communication.
• Ultra-compact and lightweight design.

2.2 Què hi ha a la caixa

• 1x M5NanoC6 Development Kit

2.3 Identificació de components

Figure 1: M5Stack NanoC6 Component Layout. This image displays the M5Stack NanoC6 development board from two angles, highlighting key components such as the 2.4G ceramic antenna, USB-C port, LED (G7), IR emitter (G3), Button (G9), RGB (G20), RGB PWR (G19), and Grove port (G1, G2, 5V, G). It also indicates the ESP32-C6FH4 microcontroller and supported protocols like Wi-Fi 6, Matter, Thread, and Zigbee. The dimensions (23.5x12x9.5mm) and weight (2.5g) are also shown.

Figure 2: M5Stack NanoC6 Front View. Un primer pla view of the M5Stack NanoC6 development kit, showing its compact blue casing and the USB-C port. The M5 logo is visible on the top surface.

3. Instruccions de configuració

3.1 Connexió del dispositiu

1. Locate the USB-C port on the M5NanoC6.
2. Connect the M5NanoC6 to your computer using a compatible USB-C data cable.
3. Ensure your computer recognizes the device. You may need to install appropriate drivers for the ESP32-C6FH4 chipset if not automatically detected.

3.2 Entering Download Mode for Programming

To upload firmware or programs to the M5NanoC6, the device must be placed into download mode.

1. Identify the button labeled G9 on the NanoC6 (refer to Figure 1).
2. Mantén premut the G9 button.
3. While holding the G9 button, connect the USB-C data cable to your computer.
4. Release the G9 button once the device is connected. The NanoC6 is now in download mode and ready for programming.

3.3 Expanding with Grove Modules

The M5NanoC6 features a Grove interface, allowing for easy connection to a wide range of M5Stack Grove modules.

1. Identify the Grove port on the NanoC6 (refer to Figure 1).
2. Connect your desired Grove module using a compatible Grove cable.
3. Ensure the module's communication protocol (e.g., UART, I2C) is compatible with the NanoC6's capabilities.

Figure 3: M5Stack NanoC6 Grove Port. Aquesta imatge mostra un costat view of the M5Stack NanoC6, highlighting the white Grove connector for attaching expansion modules.

4. Instruccions de funcionament

4.1 Comunicació sense fil

The M5NanoC6 supports multiple advanced wireless protocols via its ESP32-C6FH4 MCU:

• Wi-Fi 6 (802.11ax): Provides higher speed, greater capacity, lower latency, and stronger security compared to previous Wi-Fi standards. It is backward compatible with 802.11b/g/n.
• Zigbee 3.0: A low-power, low-data-rate wireless mesh network standard for IoT devices.
• Thread 1.3: An IPv6-based mesh networking protocol for connecting IoT devices.
• Matèria: An open-source connectivity standard for smart home devices, built on IP.

Refer to the ESP-IDF documentation or M5Stack's official resources for specific programming examples and libraries to utilize these protocols.

4.2 Infrared Emitter

The built-in infrared LED (G3) allows the NanoC6 to control various infrared IoT devices, such as televisions, air conditioners, or audio systems.

• Program the NanoC6 to send specific IR codes corresponding to your target device's remote control signals.
• The effective emission distance varies with the angle: up to 632cm at 0°, 83cm at 45°, and 29cm at 90°.

4.3 Programmable RGB LEDs

The NanoC6 includes programmable RGB LEDs (G20, G19) that can be used for visual feedback, status indicators, or aesthetic effects in your projects. These are typically WS2812 compatible.

• Utilize appropriate libraries (e.g., NeoPixel library for Arduino) to control the color and brightness of the RGB LEDs.

5. Manteniment

To ensure the longevity and optimal performance of your M5Stack NanoC6 Development Kit, follow these general maintenance guidelines:

• Manejar amb cura: Eviteu deixar caure o sotmetre el dispositiu a cops físics.
• Mantenir sec: Protect the device from moisture and liquids. Operate it in a dry environment.
• Neteja: Keep the USB-C port and Grove connector free from dust and debris. Use a soft, dry brush if cleaning is necessary.
• Temperatura: Operate within the specified operating temperature range of 0-40°C.
• Font d'alimentació: Use a stable 5V DC power supply via the USB-C port.

6. Solució De Problemes

If you encounter issues with your M5Stack NanoC6, refer to the following troubleshooting tips:

7. Especificacions

Figure 4: M5Stack NanoC6 Technical Specifications. This image presents a table detailing various technical parameters of the M5NanoC6, including SoC, Wi-Fi protocol, RGB type, IR remote control parameters, Grove outputs maximum current, standby current (Deep Sleep and ULP modes), operating current, Wi-Fi stretch test results, and operating temperature.

8. Garantia i Suport

For information regarding product warranty, technical support, and additional resources, please refer to the official M5Stack weblloc o poseu-vos en contacte amb el seu servei d'atenció al client.

M5Stack Official Store: Visit the M5Stack Store on Amazon