X-PRO Fiji 150 Moped Scooter User Manual

1. Introducció

Welcome to the X-PRO Fiji 150 Moped Scooter user manual. This document provides essential information for the safe and efficient operation, maintenance, and care of your new scooter. Please read this manual thoroughly before operating the vehicle to ensure your safety and to maximize the lifespan of your scooter. The X-PRO Fiji 150 is a 150cc, 4-stroke moped featuring 13-inch aluminum wheels and both electric and kick start capabilities.

Figura 1: Frontal esquerre view of the X-PRO Fiji 150 Moped Scooter, showcasing its design and 13-inch aluminum wheels.

2. Informació de seguretat

Operating a moped requires attention to safety. Always prioritize your safety and the safety of others. Failure to follow these instructions may result in serious injury or death.

• Utilitzeu equip de protecció: Always wear an approved helmet, eye protection, gloves, and appropriate riding attire.
• Inspecció prèvia a la marxa: Before each ride, check tire pressure, brake function, fluid levels, lights, and horn.
• Familiarize Yourself with Controls: Understand the function of all controls, including the engine kill switch, before riding.
• Condicions de la carretera: Be aware of road conditions, traffic, and weather. Ride defensively.
• Seguretat dels passatgers: If carrying a passenger, ensure they are properly seated and aware of safety protocols.
• Muffler Cover: The scooter is equipped with a muffler cover designed to prevent accidental injury from hot components. Do not remove or tamper with this cover.
• Advertència de la proposta 65: Aquest producte pot contenir productes químics coneguts a l’Estat de Califòrnia per causar càncer i defectes congènits o altres danys reproductius.

3. Setup and Initial Checks

Your X-PRO Fiji 150 Moped Scooter arrives approximately 99% assembled. The following steps outline the final setup and crucial initial checks before your first ride.

Figure 2: The X-PRO Fiji 150 Moped Scooter as packaged for transport in its fully assembled version.

3.1 Uncrating and Minor Assembly

Carefully remove the scooter from its packaging. While largely assembled, some minor components like mirrors or the front wheel may require attachment. Refer to the specific assembly guide included with your scooter for detailed instructions on these final steps.

3.2 Essential Pre-Ride Checks

1. Nivells de líquids: Verify engine oil, brake fluid, and fuel levels are at their recommended marks. Top up if necessary using appropriate fluids.
2. Pressió dels pneumàtics: Check both front and rear tire pressures. Ensure they match the specifications listed in this manual or on the tire sidewall.
3. Funció de fre: Test both front (disc) and rear (drum) brakes for proper operation and responsiveness.
4. Controls: Confirm the throttle operates smoothly and returns to idle. Check that the headlight, tail light, turn signals, and horn are functional. Test the engine kill switch.
5. Elements de fixació: Inspect all visible nuts, bolts, and fasteners to ensure they are tight and secure.
6. Connexió de la bateria: Ensure the 12V/7Ah battery is securely connected.

4. Instruccions de funcionament

4.1 Arrencada del motor

The X-PRO Fiji 150 offers both electric and kick start options.

• Arrencada elèctrica: Ensure the engine kill switch is in the 'RUN' position. Insert the key and turn it to 'ON'. Apply the rear brake lever and press the electric start button. Release the button once the engine starts.
• Inici de sessió: If the electric start is unavailable or preferred, ensure the engine kill switch is in the 'RUN' position and the key is 'ON'. Place the scooter on its center stand. Firmly push down the kick start lever with your foot until the engine starts.

4.2 Controls and Riding

• Acceleració: Gently twist the right handlebar grip towards you to accelerate. Release to decelerate.
• Frens: The right lever controls the front disc brake, and the left lever controls the rear drum brake. Apply both smoothly and progressively.
• Llums: The headlight and tail light activate with the ignition. Use the handlebar switch for high/low beam.
• Senyals de gir: Use the switch on the left handlebar to indicate turns. Remember to manually cancel the signal after completing your turn.
• Trompa: Press the button on the left handlebar to sound the horn.
• Engine Kill Switch: Located on the right handlebar, this switch immediately cuts power to the engine in an emergency.

Figura 3: Part posterior dreta view of the scooter, highlighting the exhaust system and rear wheel.

5. Manteniment

Regular maintenance is crucial for the longevity and safe operation of your X-PRO Fiji 150 Moped Scooter. Perform checks and services as outlined below.

5.1 Routine Checks (Before Each Ride)

• Pneumàtics: Inspect for proper inflation, wear, and damage.
• Frens: Check brake lever free play and effectiveness.
• Lights & Horn: Verify all lights and the horn are working.
• Fuites de fluids: Look for any signs of oil or brake fluid leaks.

5.2 Manteniment programat

• Oli de motor: Check oil level regularly and change according to the manufacturer's recommendations (typically every 500-1000 miles or 3-6 months).
• Filtre d'aire: Inspect and clean or replace the air filter periodically, especially in dusty conditions.
• Bujía: Inspeccioneu i netegeu o substituïu la bugia segons calgui.
• Sistema de fre: Inspect brake pads/shoes for wear and replace if necessary. Check brake fluid level and condition.
• Bateria: Check battery terminals for corrosion and ensure connections are tight. If applicable, check electrolyte levels.
• Tire Wear: Monitor tire tread depth and replace tires when they reach the wear indicators.

Figura 4: Pro lateralfile of the X-PRO Fiji 150 Moped Scooter, illustrating its overall dimensions.

6. Solució De Problemes

This section addresses common issues you might encounter with your X-PRO Fiji 150 Moped Scooter. For problems not listed here, or if you are unsure, consult a qualified technician.

6.1 El motor no arrenca

• Comprovació de combustible: Assegureu-vos que hi hagi prou combustible al dipòsit.
• Interruptor de mort: Verify the engine kill switch is in the 'RUN' position.
• Posició clau: Confirm the ignition key is turned to 'ON'.
• Palanca de fre: For electric start, ensure a brake lever is squeezed.
• Bateria: If using electric start, check if the battery is charged. A weak battery may prevent starting.
• Bujía: Inspeccioneu la bugia per si hi ha brutícia o danys.

6.2 Poor Engine Performance

• Filtre d'aire: A clogged air filter can restrict airflow. Clean or replace it.
• Qualitat del combustible: Ensure you are using fresh, clean fuel.
• Bujía: A worn or incorrectly gapped spark plug can affect performance.

6.3 Els llums no funcionen

• Bombeta: Check if the bulb is burnt out and replace if necessary.
• Cablejat: Inspeccioneu el cablejat per detectar connexions soltes o danys.
• Fusibles: Check the fuse box for any blown fuses.

7. Especificacions

Detailed technical specifications for the X-PRO Fiji 150 Moped Scooter.

8. Garantia i Suport

8.1 Informació de la garantia

The X-PRO Fiji 150 Moped Scooter comes with a 1 mesos de garantia from the date of purchase. This warranty covers manufacturing defects under normal use. Please retain your proof of purchase for any warranty claims. The warranty does not cover damage resulting from misuse, neglect, accidents, or unauthorized modifications.

8.2 Atenció al client

For technical assistance, parts inquiries, or warranty claims, please contact the seller, XPROUSA, directly. You can typically find their contact information on your purchase receipt or through the platform where the scooter was purchased. When contacting support, please have your model number (MC-NN023-Assembled) and purchase details readily available.