1. Introducció
This manual provides detailed instructions for the proper use and maintenance of your UHPPOTE RF Wireless Remote Control Transmitter, Model HBK-T01. This device is designed to operate compatible UHPPOTE RF remote control systems, such as gate openers, door access controls, and other 433.92MHz RF receivers. Please read this manual thoroughly before operation to ensure safe and effective use.
Figure 1.1: UHPPOTE HBK-T01 RF Wireless Remote Control Transmitters (3-Pack)
2. Producte acabatview
2.1 Característiques clau
- Freqüència de transmissió: 433.92MHz. This remote is only compatible with UHPPOTE RF remote control systems operating on this frequency.
- Fixed Code: The remote utilizes a fixed code system, allowing for straightforward programming.
- Programable: This remote control is shipped with an empty code and requires user programming to function with your specific receiver.
- Font d'alimentació: Powered by 2pcs CR2016 batteries (included).
- Durada de la bateria: Tested for approximately 50,000 cycles.
2.2 Components
Cada paquet inclou:
- UHPPOTE HBK-T01 RF Wireless Remote Control Transmitter
- 2 x CR2016 Batteries (pre-installed or included separately)
Figure 2.1: Ergonomic Design and Wireless Signal Transmission
Figure 2.2: Compact Remote with Integrated Keychain Loop
Figura 2.3: posterior View Showing Model Number HBK-T01 and FCC ID
3. Configuració i programació
3.1 Instal·lació/substitució de la bateria
The remote control is powered by two CR2016 batteries. If the remote is not responding or the indicator light is dim, the batteries may need replacement.
- Locate the small screws on the back of the remote control.
- Using a small screwdriver, carefully remove the screws and open the casing.
- Traieu les piles CR2016 velles.
- Insert two new CR2016 batteries, ensuring correct polarity (+ and -).
- Tanca el casing and secure it with the screws.
Figure 3.1: Battery Replacement Guide for CR2016 Batteries
3.2 Programació del comandament a distància
The HBK-T01 remote control is shipped with an empty code and s'han de programar to your specific UHPPOTE receiver unit before use. The programming procedure is typically performed on the receiver unit itself, not on the remote control.
Important: Programming instructions vary depending on the specific UHPPOTE receiver model you are using. Please refer to the instruction manual provided with your UHPPOTE receiver for detailed programming steps. If you do not have the receiver's manual or require further assistance, please contact UHPPOTE customer support.
Figure 3.2: Integration with Electric Lock Systems (Receiver required)
4. Instruccions de funcionament
Once the HBK-T01 remote control is successfully programmed to your UHPPOTE receiver, operation is straightforward:
- Ensure the receiver unit is powered on and within range.
- Press the button on the HBK-T01 remote control.
- The remote will transmit an RF signal to the programmed receiver.
- The receiver will then activate the connected device (e.g., open a gate, unlock a door, turn on a light).
The blue LED indicator on the remote will illuminate when the button is pressed, indicating signal transmission.
Figure 4.1: Versatile Applications of the HBK-T01 Remote Control
5. Manteniment
- Neteja: Netegeu el comandament a distància amb un drap suau i sec. No utilitzeu productes de neteja abrasius ni dissolvents.
- Comprovació de la bateria: If the remote's performance degrades, check and replace the batteries as described in Section 3.1.
- Emmagatzematge: Guardeu el comandament a distància en un lloc fresc i sec, lluny de la llum solar directa i de temperatures extremes.
- Evitar l'impacte: Do not drop or subject the remote control to strong impacts, as this may damage internal components.
6. Solució De Problemes
| Problema | Causa possible | Solució |
|---|---|---|
| Remote does not respond / No LED light | Piles gastades o instal·lades incorrectament. | Replace batteries (CR2016) and ensure correct polarity. |
| Remote LED lights up, but device does not respond | Remote not programmed to receiver, or receiver is out of range/powered off. | Verify programming with receiver's manual. Ensure receiver is powered and within operating range. Check receiver's status. |
| Limited operating range | Obstructions (walls, metal structures), radio interference, low battery. | Move closer to the receiver. Remove obstructions. Check for sources of interference. Replace batteries. |
| El comandament a distància funciona de manera intermitent | Low battery, intermittent interference. | Replace batteries. Try operating from a different location to rule out interference. |
7. Especificacions
- Marca: UHPPOTE
- Número de model: HBK-T01
- Color: Negre
- Font d'alimentació: Funciona amb bateria
- Bateries: 2 x CR2016 (inclòs)
- Voltage: 6 Volts
- Freqüència de transmissió: 433.92 MHz
- Tecnologia de connectivitat: Sense fil (RF)
- Mètode de control: Remot
- Dispositius compatibles: UHPPOTE's RF remote control receivers
- Dimensions de l'article (L x A x A): 2.3 x 1.3 x 0.5 polzades (5.84 x 3.30 x 1.27 cm)
- Pes de l'article: 4.6 unces (130 grams)
- Tipus d'instal·lació: Bricolatge sense fil
- Tipus d'alerta: Entry Only (refers to typical application with entry systems)
8. Garantia i Suport
8.1 Informació de la garantia
For detailed warranty information regarding your UHPPOTE HBK-T01 remote control, please refer to the warranty card included with your purchase or visit the official UHPPOTE weblloc web. Els termes i condicions de la garantia poden variar segons la regió i el distribuïdor.
8.2 Atenció al client
If you encounter any issues, have questions about programming, or require technical assistance, please contact UHPPOTE customer support. You can typically find contact information on the product packaging, the UHPPOTE official weblloc web o a través del vostre punt de compra.
Oficial de la UHPPOTE Weblloc: Visit UHPPOTE Store on Amazon
