2 Button ARC 128 Garage Opener Remote

Introducció

This manual provides comprehensive instructions for the proper use, setup, and maintenance of your BENINCA TO.GO 2A Transmitter. Please read this manual carefully before operating the device to ensure optimal performance and longevity.

Producte acabatview

The BENINCA TO.GO 2A is a 2-channel garage opener remote control designed for use with compatible BENINCA ARC systems. It operates on a frequency of 433.92 MHz and utilizes a universal code, including both rolling code and Advanced Rolling Code (ARC) technology, for enhanced security.

Què és l'ARC? The Advanced Rolling Code (ARC) technology significantly enhances security by using a 128-bit transmitted code, which is a substantial improvement over the previous 64-bit versions. This advanced encryption makes unauthorized duplication extremely difficult, providing maximum safety for your garage access.

Figura 1: Frontal view of the BENINCA TO.GO 2A Transmitter, showing its two white control buttons and the BENINCA logo at the bottom.

Configuració

1. Instal·lació de la bateria

The BENINCA TO.GO 2A Transmitter is powered by a 12V A23 battery. The battery is typically pre-installed. If replacement is needed, carefully open the remote casing (refer to the Maintenance section for battery replacement) and insert a new 12V A23 battery, ensuring correct polarity.

2. Pairing with Your Receiver

To operate your garage door, the TO.GO 2A Transmitter must be paired with your BENINCA garage door opener receiver. The exact pairing procedure may vary depending on your specific BENINCA receiver model. Generally, the process involves:

1. Locating the "PROG" or "MEMO" button on your garage door opener's receiver unit. This button is usually found on the control board of the opener.
2. Pressing and holding the "PROG" or "MEMO" button on the receiver until an indicator light (LED) illuminates or flashes, indicating it is in programming mode.
3. Within a few seconds, press the desired button on your new TO.GO 2A Transmitter that you wish to use for operating the garage door. Hold the button until the receiver's indicator light changes (e.g., turns off, flashes rapidly, or becomes solid), confirming successful pairing.
4. Deixeu anar el botó del transmissor.
5. Test the transmitter by pressing the programmed button. The garage door should respond.

Important: For detailed and specific pairing instructions, please refer to the user manual of your BENINCA garage door opener receiver.

Instruccions de funcionament

Once the BENINCA TO.GO 2A Transmitter is successfully paired with your garage door opener receiver, operation is straightforward:

• Opening/Closing the Garage Door: Press the programmed button on the transmitter once. The garage door will begin to open or close. Pressing the button again during operation will typically stop the door.
• Portes múltiples: If you have programmed both buttons to control different garage doors, ensure you press the correct button for the desired door.
• Interval: The effective operating range of the transmitter can be affected by environmental factors, such as interference from other radio frequencies, building materials, and battery strength. For best results, operate the remote within a reasonable distance from the receiver.

Manteniment

Canvi de bateria

When the operating range decreases significantly or the indicator light on the transmitter (if present) does not illuminate, it may be time to replace the battery.

1. Locate the small notch or seam on the side or bottom of the transmitter casing.
2. Using a small flat-head screwdriver or a coin, carefully pry open the casing at the notch. Apply gentle pressure to avoid damaging the plastic.
3. Remove the old 12V A23 battery. Note its orientation (positive and negative terminals).
4. Insert a new 12V A23 battery, ensuring it is placed with the correct polarity.
5. Alineeu les dues meitats de la casing i premeu-les fermament fins que encaixin al seu lloc.
6. Test the transmitter to ensure it functions correctly.

Neteja

Clean the exterior of the transmitter with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the casing or internal components. Avoid exposing the transmitter to excessive moisture.

Resolució de problemes

Especificacions