SenseCAP Card Tracker T1000-E User Manual

1. Introducció

The SenseCAP Card Tracker T1000-E is a versatile, compact device designed for Meshtastic communication. Featuring nRF52840 and LR1110 chips, it supports LoRa (863-928 MHz ISM bands), Bluetooth 5.0, Thread, and Zigbee, ensuring broad compatibility. Integrated with a Mediatek AG3335 GPS chip, it provides high-precision positioning services. This manual provides detailed instructions for setup, operation, maintenance, and troubleshooting to ensure optimal performance of your device.

Davant view of the SenseCAP Card Tracker T1000-E, showcasing el seu disseny compacte.

The T1000-E is IP65-rated, making it suitable for outdoor use and resistant to water splashes.

2. Primers passos

2.1 Què hi ha a la caixa

Upon unboxing your SenseCAP Card Tracker T1000-E, please ensure all the following items are present:

• SenseCAP Card Tracker T1000-E Device
• USB Charging Cable (4-pin magnetic)
• Manual d'usuari (aquest document)

The SenseCAP Card Tracker T1000-E, its magnetic USB charging cable, and the user manual.

2.2 Encès inicial

To power on your T1000-E device, press the button once and hold for approximately 5 seconds. The device will emit an ascending melody, and the LED will light up for 0.5 seconds, indicating successful power-on.

3. Instruccions de funcionament

3.1 Indicadors d'estat

The LED on the T1000-E provides visual feedback on its operational status:

• Randomly Flashing LED: Indicates that the T1000-E is operating normally.
• LED Lights Up for 0.5s, then Off for 0.5s (in a loop): Indica que el dispositiu s'està carregant.
• LED Stays On Continuously: Indicates the device is in DFU (Device Firmware Update) mode.

3.2 Receiving Messages

In firmware version 2.4.2, the T1000-E does not make a sound when receiving messages by default. To enable audible notifications, you need to configure this manually via the Meshtastic app:

1. Go to the "Settings" section in the Meshtastic app.
2. Click on "External Notification".
3. Enable all desired notification settings, such as "Alert when receiving a message".
4. Ensure the correct GPIO pins are configured for the buzzer (Pin 25) and LED (Pin 24) if applicable.
5. Click "Save". The device will reboot, and the buzzer will play an ascending melody with a brief LED flash upon successful configuration.

Once configured, when a message is received, the buzzer will play an ascending melody, and the LED will flash once.

3.3 Enviament de missatges

When sending a message from the Meshtastic app, there is no direct hardware indication on the T1000-E itself. You can confirm whether the message was sent successfully by checking the notifications within the chat interface of the Meshtastic app.

3.4 Funcionalitat del GPS

The T1000-E can broadcast its node and location information. To trigger this, double-press the button on the device. The information can be reviewed from the serial port if connected to a computer.

To toggle the GPS function on or off, triple-press the button on the device.

4. Manteniment

4.1 Càrrega

To charge your T1000-E, connect the 4-pin magnetic charging cable to the device. The LED will light up for 0.5 seconds and then turn off for 0.5 seconds in a repeating cycle, indicating that the device is charging.

4.2 Actualització del microprogramari

Updating the firmware on your T1000-E is crucial for new features and bug fixes. Meshtastic uses the littlefs library to store configuration, logs, and other data in the internal flash. Updating the firmware does not erase this additional data, which can cause issues if the format or location of data changes between releases. Therefore, it is recommended to perform a factory reset before updating the firmware.

To enter DFU (Device Firmware Update) mode for flashing firmware:

1. Connect the T1000-E to your computer using the 4-pin magnetic charging cable. Ensure the data cable is securely connected, as a loose connection can affect the flashing process.
2. Manteniu premut el botó del dispositiu.
3. While holding the button, connect the charging cable magnetically twice in quick succession (interval between presses should be around 500ms).
4. Release the button. The LED will stay on continuously, indicating that the device is in DFU mode. Your computer should display a USB drive named "T1000-E", allowing you to copy the firmware onto it.

After the firmware transfer is complete, the device will automatically restart and boot with the new firmware.

4.3 Restabliment del dispositiu

If you need to reset your T1000-E, you can use the charging cable:

1. Manteniu premut el botó del dispositiu.
2. While holding the button, connect the magnetic charging cable once.
3. Release the button. The previously flashing LED will turn off. Wait for the buzzer to sound, and the LED will light up briefly. This indicates that the device has restarted successfully and will then enter charging mode.

5. Solució De Problemes

5.1 Bluetooth Connection Issues After Firmware Update

If you find that the Bluetooth connection is not working after a firmware update, follow these steps:

1. Go to the Bluetooth list in your phone's settings.
2. Remove (forget) the corresponding Bluetooth name for your T1000-E.
3. Return to the Meshtastic app and attempt to reconnect. You may need to re-pair the device.

5.2 General Connectivity and Range

The T1000-E is designed for long-range, low-power communication. Factors affecting range include line-of-sight, obstacles, and environmental interference. For optimal performance, consider placement in areas with clear line-of-sight to other Meshtastic nodes.

5.3 Durada de la bateria

The T1000-E offers solid battery life due to its nRF52840 chipset. To conserve power when not actively using the device, it is recommended to power it off. Simply press and hold the button for about 5 seconds until the buzzer plays a descending melody, indicating the device has been turned off.

6. Especificacions del producte

6.1 Detalls tècnics

Physical dimensions of the T1000-E, highlighting its credit card size and slim profile.

7. Garantia i Suport

The SenseCAP Card Tracker T1000-E is manufactured by seeed studio. For specific warranty information, technical support, or further inquiries, please refer to the official seeed studio weblloc web o contacteu directament amb el servei d'atenció al client. Conserveu el rebut de compra per a reclamacions de garantia.