Introducció
This manual provides essential information for the proper installation, operation, and maintenance of your DD Audio 510E-D2 10" Dual 2-Ohm 2100W Subwoofers. Please read this manual thoroughly before installation and use to ensure optimal performance and longevity of your product.
Informació de seguretat
- Desconnecteu sempre la bateria del vehicle abans de realitzar qualsevol treball elèctric.
- Ensure proper wiring and impedance matching to prevent damage to the subwoofers and ampmés viu.
- Avoid exposing subwoofers to excessive moisture or extreme temperatures.
- Securely mount the subwoofers to prevent movement during vehicle operation.
- Prolonged exposure to high sound pressure levels can cause permanent hearing damage.
Característiques del producte
The DD Audio 510E-D2 subwoofers incorporate advanced design elements for high performance:
- Free Flow Cooling System
- High-temperature Voice Coil
- Dual Layer Spider System with Integrated Tinsel Leads
- Extended Pole Piece
- Double Stitched EROM Surrounds
- Fiberglass Loaded Non-Pressed Cones
- Embossed DDesign Magnet Boot
- 3-inch Voice Coils with 120oz Magnet Motors
- Increased Xmax (50% increase)
Imatge: Frontal i lateral view of the DD Audio 510E-D2 subwoofers, highlighting their robust construction.
Configuració i instal·lació
Proper installation is crucial for the performance and longevity of your subwoofers. If you are unsure about any steps, consult a professional installer.
1. Enclosure Recommendations
For optimal performance, DD Audio recommends a ported enclosure with a volume of 1.25 - 1.5 peus cúbics per subwoofer. Ensure the enclosure is well-constructed and sealed to prevent air leaks.
2. Muntatge
- Ensure the mounting surface is sturdy and free from obstructions.
- Cut a circular opening with a diameter of 8.93 polzades for each subwoofer.
- Fixeu el subwoofer a la carcassa amb els cargols adequats, assegurant-vos que estigui ben segellat.
- The mounting depth required is 5.9 polzades.
Imatge: Frontal view of the DD Audio 510E-D2 subwoofers, illustrating the cone and surround design.
3. Cablatge
The 510E-D2 subwoofers are Dual 2-Ohm (D2) voice coil models. Proper wiring is essential to match the impedance requirements of your amplifier. Consult your ampmanual del lificador per a càrregues d'impedància compatibles.
Example Wiring for a Pair of D2 Subwoofers:
- 1 Ohm Final Load: Wire each subwoofer's voice coils in parallel (resulting in 1 Ohm per subwoofer). Then, wire both 1 Ohm subwoofers in parallel to the ampmés viu.
- 2 Ohm Final Load: Wire each subwoofer's voice coils in series (resulting in 4 Ohms per subwoofer). Then, wire both 4 Ohm subwoofers in parallel to the ampmés viu.
- 4 Ohm Final Load: Wire each subwoofer's voice coils in series (resulting in 4 Ohms per subwoofer). Then, wire both 4 Ohm subwoofers in series to the ampmés viu.
Always use appropriate gauge speaker wire for your power levels and cable runs. Ensure all connections are secure and insulated.
Imatge: Lateral view of the DD Audio 510E-D2 subwoofers, highlighting the magnet boot and terminal connections.
Instruccions de funcionament
- Període d'entrada: Allow a break-in period of approximately 20-30 hours of normal listening before operating the subwoofers at high power levels. This allows the suspension components to loosen and perform optimally.
- Configuració de guany: Estableix el teu ampguany del lificador correctament per coincidir amb el volum de sortidatage de la unitat principal. Una configuració de guany incorrecta pot provocar distorsió i danys.
- Configuració de crossover: Feu servir un filtre de pas baix (LPF) al vostre amplifier or head unit to send only low frequencies to the subwoofers. A typical LPF setting for subwoofers is between 60Hz and 100Hz.
- Filtre subsònic: Si el teu amplifier has a subsonic filter, set it slightly below your enclosure's tuning frequency to protect the subwoofers from over-excursion at very low frequencies.
- Seguiment: Listen for signs of distortion or stress from the subwoofers. If you hear distortion, reduce the volume or adjust your amplifier settings immediately.
Manteniment
- Neteja: Use a soft, dry cloth to clean the subwoofer cones and surrounds. Avoid using harsh chemicals or excessive moisture.
- Inspecció: Periodically inspect the subwoofer surrounds, cones, and wiring connections for any signs of wear, damage, or corrosion.
- Protecció del medi ambient: Protect the subwoofers from direct sunlight, extreme temperatures, and moisture, which can degrade materials over time.
Resolució de problemes
| Problema | Causa possible | Solució |
|---|---|---|
| Sense so | Sense poder amplifier, loose wiring, incorrect input signal, amplificador en mode de protecció. | Comproveu amplifier power and ground connections. Verify RCA and speaker wire connections. Ensure amplifier is not in protect mode. |
| So distorsionat | Amplifier gain too high, incorrect crossover settings, damaged subwoofer, ampretall de lifier. | Reduir amplifier gain. Adjust LPF and subsonic filter settings. Inspect subwoofer for physical damage. |
| Sortida de greus feble | Incorrect wiring impedance, phase issues, insufficient amplifier power, poor enclosure design. | Verificar les coincidències d'impedància del cablejat amplifier. Check phase setting on amplifier/head unit. Ensure amplifier provides adequate power. Review enclosure specifications. |
| Sobreescalfament del subwoofer | Overpowering, incorrect impedance, insufficient cooling, prolonged high volume use. | Reduce power. Verify impedance. Ensure adequate ventilation around the subwoofer and ampmés viu. |
Imatge: De dalt a baix view of the DD Audio 510E-D2 subwoofers, showcasing the magnet boot design.
Especificacions
| Característica | Detall |
|---|---|
| Nom del model | 510E-D2 |
| Tipus d'altaveu | Subwoofer |
| Mida de l'altaveu | 10 polzades |
| Diàmetre del woofer | 10 polzades |
| Watts RMS | 700 Watts (per subwoofer) |
| Watts Peak | 2100 Watts (per subwoofer) |
| Impedància | Dual 2-Ohm (D2) |
| Voice Coil Diameter (VCD) | 3 polzades |
| Fs (Freqüència de ressonància) | 38 Hz |
| Qms (Mechanical Q) | 4.96 |
| Qes (Electrical Q) | 0.76 |
| Qts (Total Q) | 0.65 |
| Vas (Equivalent Volume) | 37.1 litres |
| BL (Motor Strength) | 25 TM |
| Xmech (Mechanical Excursion) | 30 MM |
| Xmax (excursió lineal) | 18 MM |
| Frame OD (Outer Diameter) | 10 polzades |
| Frame OD w/Gasket | 10.4 polzades |
| Diàmetre de muntatge | 8.93 polzades |
| Profunditat de muntatge | 5.9 polzades |
| Diàmetre del motor | 7 polzades |
| Motor Depth | 2.375 polzades |
| Pes de l'imant | 120 oz |
| Desplaçament del woofer | 0.7 CuFt |
| Tancament portat recomanat | 1.25 - 1.5 CuFt |
| Pes de l'article (parell) | 38 lliures |
| Tecnologia de connectivitat | RCA, Speaker Wire |
| Tipus de muntatge | Muntatge de cotxe |
Informació de la garantia
The DD Audio 510E-D2 subwoofers come with a Garantia limitada. Please refer to the official DD Audio website or contact their customer support for specific terms and conditions regarding warranty coverage, duration, and claims procedures.
Typically, warranties cover manufacturing defects and do not cover damage caused by improper installation, abuse, or exceeding recommended power limits.
Atenció al client
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact DD Audio customer support:
- Visit the official DD Audio weblloc web per a recursos de suport i informació de contacte.
- Refer to your purchase documentation for reseller-specific support options.
