Gazzyt Foldable Racing Wheel Stand Instruction Manual

Introducció

Thank you for choosing the Gazzyt Foldable Racing Wheel Stand. This manual provides essential information for the proper assembly, operation, and maintenance of your new racing peripheral stand. Designed for compatibility with a wide range of popular racing wheels, pedals, and shifters, this stand offers a stable and adjustable platform to enhance your sim racing experience. Please read this manual thoroughly before use to ensure optimal performance and safety.

Informació de seguretat

• Ensure all bolts and fasteners are securely tightened before each use. Loose connections can lead to instability and potential injury.
• Do not exceed the maximum weight capacity of the stand. Refer to the specifications section for details.
• Keep hands and fingers clear of moving parts during adjustment to prevent pinching or crushing.
• Place the stand on a flat, stable, and non-slip surface to prevent accidental tipping.
• When folding or unfolding the stand, proceed with caution to avoid sudden movements.
• This product is intended for adult use. Keep out of reach of small children.

Contingut del paquet

Si us plau, comproveu que tots els components siguin presents abans de començar el muntatge:

• Gazzyt Foldable Racing Wheel Stand Frame
• Placa de roda
• Placa de pedals
• Shifter/Handbrake Platform
• Portavasos
• Assembly Hardware (bolts, nuts, washers, adjustment knobs)
• Eines de muntatge (claus, claus hexagonals)
• Manual d'instruccions

Note: Steering wheel, pedals, and shifter are not included with this product.

Muntatge i muntatge

The Gazzyt Racing Wheel Stand arrives approximately 80% pre-assembled. Follow these steps to complete the setup:

1. Unfold the Main Frame: Carefully unfold the main frame of the stand until it locks into its open position. Ensure all locking mechanisms are engaged.
2. Attach the Wheel Plate: Secure the wheel plate to the top section of the stand using the provided bolts and adjustment knobs. Ensure it is firmly attached.
3. Instal·leu la placa del pedal: Position the pedal plate at the base of the stand and secure it with the designated hardware. The angle can be adjusted later.
4. Mount the Shifter/Handbrake Platform: Attach the shifter/handbrake platform to either the left or right side of the stand, according to your preference, using the appropriate bolts.
5. Attach the Cup Holder: Secure the cup holder to the designated mounting point on the stand.
6. Munta els teus perifèrics: Attach your racing wheel, pedals, and shifter to their respective plates using the pre-drilled holes. Ensure all devices are securely fastened.

Figura 1: The Gazzyt Foldable Racing Wheel Stand fully assembled with a racing wheel and pedals. This image illustrates the general layout and appearance of the stand once peripherals are mounted.

Figura 2: Stand dimensions, showing height adjustable from 22 to 34 inches, width 21 inches, and depth 22 inches. A cup holder is also visible.

Figura 3: This image highlights the adjustable pedal angle, adjustable steering wheel panel, and height-adjustable stand features, allowing for personalized ergonomic setup.

Instruccions d'ús i ajustos

The Gazzyt Racing Wheel Stand is designed for maximum adjustability to suit various users and racing setups. Utilize the adjustment knobs and levers to customize your experience.

Ajust del suport:

• Ajust d'alçada: Loosen the adjustment knobs on the main vertical supports to raise or lower the wheel plate to your desired height. Retighten securely.
• Wheel Plate Angle: The steering wheel panel can be adjusted for tilt. Loosen the relevant fasteners, set the angle between -4° to 4°, and then retighten.
• Pedal Angle: Adjust the angle of the pedal plate by loosening the bolts at its base, setting the preferred tilt, and then securely tightening them.
• Shifter/Handbrake Position: The dedicated platform for shifters and handbrakes can be positioned on either side of the stand and adjusted for distance and angle to optimize ergonomics.

Compatibilitat:

This stand is universally compatible with most major racing peripheral brands, including:

• Logitech (G29, G920, G923)
• Thrustmaster (T248, T300RS, TX, T500)
• Fanatec
• PXN
• Moza (R5, R9)

The pre-drilled mounting points accommodate various models. Consult your peripheral's manual for specific mounting instructions.

Figura 4: This image illustrates the X-shaped design for increased stability and the stand's ability to collapse to a compact 5-inch profile for quick storage.

Figura 5: Demonstrates the stand's compatibility with racing wheels and pedals from Thrustmaster, Logitech, Moza, and PXN, highlighting its versatile design.

Manteniment

• Neteja: Wipe down the stand regularly with a soft, damp drap. Eviteu productes de neteja abrasius o dissolvents que puguin danyar l'acabat.
• Comprovació de fixació: Periodically inspect all bolts, nuts, and adjustment knobs to ensure they remain tight. Retighten as necessary to maintain stability.
• Emmagatzematge: When not in use, the stand can be folded for compact storage. Ensure it is stored in a dry place away from extreme temperatures.

Resolució de problemes

Especificacions

• Model: steering wheel stand 26
• Marca: Gazzyt
• Material: High-strength Carbon Steel
• Dimensions del producte (desplegat): 28.46 x 30.12 x 29.53 polzades (aproximadament)
• Pes de l'article: 28.8 lliures
• Compatibilitat: Logitech G29/G920/G923, Thrustmaster T248/T300RS/TX/T500, Fanatec, PXN, Moza R5/R9
• Ajustaments: Wheel height, pedal angle, shifter position, wheel plate tilt (-4° to 4°)
• Característiques: Foldable design, wider shift platform, non-slip feet

Garantia i Suport

For warranty information, technical support, or replacement parts, please contact Gazzyt customer service through the retailer where the product was purchased or visit the official Gazzyt website. Please have your model number (steering wheel stand 26) and purchase date available when contacting support.