1. Salvaguardes importants
Please read all instructions carefully before using your Brio Sparkling 600 Series Countertop Water Cooler. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Always connect the appliance to a grounded electrical outlet.
- No submergiu l'aparell, el cable o l'endoll en aigua o altres líquids.
- Supervise children when the appliance is in use, especially when dispensing hot water, due to the risk of scalding.
- Place the appliance on a stable, level surface, away from direct sunlight and heat sources.
- Assegureu-vos una ventilació adequada al voltant de l'aparell.
- Only use CO2 cylinders with M18x1.5 thread.
2. Producte acabatview
The Brio Sparkling 600 Series Countertop Water Cooler provides instant hot, cold, room temperature, and sparkling water. It features a 2-stage filtration system and UV sterilization for clean, great-tasting water.
Components
- Sparkling Water Countertop Dispenser Unit
- Filtre de sediments
- Filtre de blocs de carboni
- Filter Flushing Housing and Tubing
- Manual d'usuari
- Refillable 5-Liter Water Tank
Guia visual
3. Configuració
Follow these steps for initial setup of your water cooler.
3.1 Desembalatge i col·locació
- Traieu tots els materials d'embalatge.
- Place the unit on a flat, stable countertop. Ensure there is at least 4 inches of clearance from walls for proper ventilation.
3.2 Filter Flushing and Installation
Before installing the filters into the unit, they must be flushed to remove carbon fines.
- Connect the provided filter flushing housing and tubing to a cold water tap.
- Attach the sediment filter (Stage 1) to the flushing housing.
- Run water through the sediment filter for 5 minutes or until the water runs clear.
- Repeat the flushing process for the carbon block filter (Stagi 2).
- Once flushed, install the sediment filter into the designated 'Stage 1' slot and the carbon block filter into the 'Stage 2' slot inside the unit. Twist to secure.
3.3 CO2 Cylinder Installation
This unit requires a 60L screw-in type CO2 cylinder with M18x1.5 thread (not included).
- Open the side panel of the water cooler.
- Carefully screw the CO2 cylinder into the designated port until hand-tight. Do not overtighten.
- Tanqueu el panell lateral.
3.4 Water Tank Filling or Direct Water Line Connection
Choose one of the following methods to supply water to your cooler:
Method A: Refillable Water Tank
- Remove the 5-liter water tank from the unit.
- Ompliu el dipòsit amb aigua potable.
- Carefully place the filled tank back into its position on the unit.
Method B: Direct Water Line Connection (Optional)
For continuous water supply, the unit can be connected to a cold-water line. Consult a qualified plumber if you are unsure about this installation.
- Locate the water inlet port at the back of the unit.
- Connect the provided water line tubing to the unit and to your cold-water supply. Ensure all connections are secure and leak-free.
- Slowly open the water supply valve to allow water to flow into the unit.
3.5 Connexió d'alimentació
Plug the power cord into a grounded electrical outlet. The unit will begin heating and cooling water. Allow approximately 15-30 minutes for water to reach desired temperatures.
4. Instruccions de funcionament
The Brio Sparkling 600 Series features a user-friendly touch-sensitive LED interface.
4.1 Funcions del tauler de control
- Botó de bloqueig: Activates/deactivates the child safety lock for hot water. Press and hold for a few seconds to unlock before dispensing hot water.
- Hot Button: Dispensa aigua calenta.
- Room Button: Dispensa aigua a temperatura ambient.
- Cold Button: Distribueix aigua freda.
- Sparkling Button: Dispenses sparkling water.
- Replace Filters Indicator: Illuminates when filters need replacement.
- Replace CO2 Indicator: Illuminates when the CO2 cylinder needs replacement.
4.2 Dispensació d'aigua
- Place your cup or container under the dispenser nozzle.
- For hot water, press and hold the Bloqueig button for a few seconds until it unlocks, then press and hold the Calent botó.
- For room, cold, or sparkling water, simply press and hold the corresponding button.
- Release the button when your desired amount of water has been dispensed.
5. Manteniment
Un manteniment regular garanteix un rendiment òptim i una llarga vida útil del vostre refrigerador d'aigua.
5.1 Cleaning the Exterior and Drip Tray
- Netegeu l'exterior amb un suau, damp tela. No utilitzeu netejadors abrasius.
- The drip tray can be removed and washed with mild soap and water. Ensure it is completely dry before reinserting.
5.2 Substitució del filtre
The 'Replace Filters' indicator will illuminate when it's time to change your filters. Recommended replacement schedule may vary based on water quality and usage.
- Joc de filtres de recanvi: Brio MIB200PKF
- Sediment Filter Only: Brio NFMPP5M
- Carbon Block Filter Only: Brio NFMCTO5MS2
To replace filters, turn off the water supply and power to the unit. Twist the old filters counter-clockwise to remove. Install new, pre-flushed filters by twisting clockwise until secure. Turn on water and power, then flush a few cups of water to remove any air.
5.3 CO2 Cylinder Replacement
The 'Replace CO2' indicator will illuminate when the cylinder is empty.
- Ensure the unit is not actively dispensing sparkling water.
- Open the side panel and unscrew the empty CO2 cylinder.
- Install a new 60L CO2 cylinder (M18x1.5 thread) as described in Section 3.3.
5.4 Autoneteja UV automàtica
This unit features an automatic UV-C self-cleaning cycle that sanitizes the cold water tank to reduce biofilm buildup and other contaminants. This process runs automatically and requires no user intervention.
6. Solució De Problemes
Consulteu aquesta secció per conèixer els problemes comuns i les seves solucions.
| Problema | Causa possible | Solució |
|---|---|---|
| No es distribueix aigua | Water tank empty or water supply off; filters clogged; power issue. | Refill water tank or check direct water line connection; replace filters; check power connection. |
| Aigua no prou calenta/freda | Unit recently plugged in; heating/cooling elements not fully engaged. | Allow 15-30 minutes for the unit to reach optimal temperatures. |
| Sense aigua amb gas | CO2 cylinder empty or improperly installed. | Check 'Replace CO2' indicator; replace or re-install CO2 cylinder. |
| Fuita de la unitat | Connexions soltes; component danyat. | Check all water line and filter connections; contact customer support if issue persists. |
| 'Replace Filters' indicator on | Filters have reached end of life. | Replace both sediment and carbon block filters. |
7. Especificacions
- Dimensions del producte (L x A x A): 19.29 x 14.4 x 16.73 polzades
- Pes: 55.1 lliures
- Número de model: CLCTPOU630UV2SB
- Capacitat del dipòsit d'aigua: 5 litres
- Sistema de filtració: 2-Stage (Sediment, Activated Carbon Block)
- Filtration Certification: NSF/ANSI 42
- Esterilització: UV-C (Automatic Self-Cleaning)
- Temperatures de l'aigua: Hot, Cold, Room Temperature, Sparkling
- CO2 Cylinder Requirement: 60L screw-in type with M18x1.5 thread (not included)
- Material: Plastic (with brushed stainless-steel exterior accents)
8. Garantia i Suport
For warranty information, technical support, or to purchase replacement parts and filters, please visit the official Brio website or contact Brio customer service. Keep your purchase receipt for warranty claims.
Brio Customer Support: Refer to your product packaging or the official Brio weblloc web per obtenir informació de contacte actualitzada.
