1. Introducció
This manual provides detailed instructions for the safe and effective operation of your ANCEL AD410 Enhanced OBD2 Scanner and ANCEL PB600 Power Circuit Probe Tester. These devices are designed to assist automotive professionals and enthusiasts in diagnosing vehicle issues and testing electrical circuits. Please read this manual thoroughly before use to ensure proper functionality and to prevent damage to the devices or your vehicle.
Image: The ANCEL AD410 OBD2 Scanner and ANCEL PB600 Power Circuit Probe Tester, showcasing their combined capabilities.
2. Informació de seguretat
Always observe the following safety precautions to avoid personal injury or damage to the vehicle or the devices:
- Perform automotive testing in a well-ventilated area.
- Utilitzeu protecció ocular que compleixi els estàndards ANSI.
- Mantingueu la roba, els cabells, les mans, les eines i l'equip de prova allunyats de totes les parts del motor en moviment o calentes.
- No connecteu ni desconnecteu cap equip de prova mentre l'encesa estigui activada o el motor estigui en marxa.
- Keep the devices dry, clean, free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the exterior.
- Do not attempt to disassemble the devices. There are no user-serviceable parts inside.
3. Producte acabatview
3.1 ANCEL AD410 Enhanced OBD2 Scanner
The ANCEL AD410 is an enhanced OBD2 scanner designed for quick and accurate vehicle diagnostics. It features a 2.4-inch TFT true-color LCD display and an intuitive user interface.
Imatge: Frontal view of the ANCEL AD410 OBD2 Scanner, showing its display and navigation buttons.
3.2 ANCEL PB600 Power Circuit Probe Tester
The ANCEL PB600 is a versatile automotive electrical circuit tester capable of performing various tests including circuit testing, battery testing, injector testing, and oscilloscope display. It comes with a 20ft extension cable for extended reach.
Image: The ANCEL PB600 Power Circuit Probe Tester, including its main unit, cables, and accessories.
Image: Diagram illustrating the ANCEL PB600's 4-in-1 capabilities: Circuit Tester, Battery Tester, Injector Tester, and Oscilloscope Tester.
Image: Infographic detailing the comprehensive features of the ANCEL PB600, including DC/AC Voltage Test, Battery Test, Frequency Test, Cranking Test, Duty Cycle Test, Relay Test, Resistance & Diode Test, Injector Signal Test, Component Activation, and Charging Test.
4. Configuració
4.1 ANCEL AD410 Setup
- Locate the vehicle's 16-pin Data Link Connector (DLC). The DLC is usually located under the dashboard on the driver's side.
- Turn the vehicle's ignition to the OFF position.
- Plug the AD410's OBD2 cable into the vehicle's DLC.
- Turn the ignition to the ON position (engine can be off or running). The AD410 will power on automatically.
4.2 ANCEL PB600 Setup
- Connecteu el cl vermellamp al terminal positiu (+) de la bateria del vehicle.
- Connecteu el cl negreamp to the negative (-) terminal of the vehicle's battery or a good chassis ground.
- The PB600 will power on once connected to a power source (8-35V DC).
5. Instruccions de funcionament
5.1 ANCEL AD410 OBD2 Scanner Operations
The AD410 provides various diagnostic functions accessible through its main menu.
Imatge: Més deview of the ANCEL AD410's diagnostic capabilities, including Read Codes, Live Data Stream, View Freeze Frame, I/M Readiness, Retrieve Vehicle Information, Erase Codes, EVAP Leak Test, DTC Lookup, O2 Sensor Test, and On-Board Monitor.
5.1.1 Read & Clear Fault Codes
This function allows you to read Diagnostic Trouble Codes (DTCs) from the vehicle's Engine Control Unit (ECU) and clear them after repairs.
- From the main menu, select "OBDII" then "Read Codes" to view current, pending, and permanent codes.
- Select "Erase Codes" to clear the DTCs and turn off the Malfunction Indicator Lamp (MIL). Assegureu-vos que el problema subjacent s'hagi resolt abans d'esborrar els codis.
Image: The ANCEL AD410 displaying options to read and erase fault codes, and the effect of turning off the check engine light.
5.1.2 Prova de preparació I/M
Checks the readiness of the emission monitoring systems to determine if the vehicle is ready for a smog test.
- From the main menu, select "I/M Readiness". The display will show the status of various monitors (e.g., MIL status, Misfire, Fuel System, Comprehensive Component).
Image: The ANCEL AD410 performing an I/M Readiness Test, showing various system statuses for emissions compliance.
5.1.3 Flux de dades en directe
Displays real-time data from the vehicle's sensors in text or graph format.
- Select "Live Data" from the OBDII menu to view various sensor readings such as engine RPM, vehicle speed, coolant temperature, etc.
5.1.4 Cerca de DTC
Proporciona definicions per als codis de diagnòstic d'errors.
- Enter a DTC code to get its detailed description.
5.1.5 Prova del sensor d'O2
Recupera els resultats de les proves del monitor del sensor d'O2 per a les proves completades més recentment de l'ordinador de bord del vehicle.
5.1.6 Prova del sistema EVAP
Initiates a leak test for the vehicle's Evaporative Emission Control (EVAP) system.
Image: The ANCEL AD410 performing an EVAP Leak Test, with a diagram illustrating the EVAP system components.
5.1.7 View Congelar fotograma
Displays a snapshot of the vehicle's operating conditions at the time a fault code was set.
5.1.8 Retrieve Vehicle Information
Recupera el número d'identificació del vehicle (VIN), l'ID de calibratge (CALID) i el número de verificació de calibratge (CVN).
5.2 ANCEL PB600 Power Circuit Probe Tester Operations
The PB600 offers a wide range of electrical testing capabilities.
5.2.1 DC/AC Voltage Prova
Mesures DC i AC voltage in a circuit.
- Touch the probe tip to the desired test point. The voltage reading will be displayed on the screen.
5.2.2 Prova de la bateria
Tests the vehicle's battery health.
5.2.3 Prova de l'injector
Tests the functionality of fuel injectors.
5.2.4 Oscilloscope Display
Provides a visual waveform display for electrical signals.
5.2.5 Prova de freqüència
Measures the frequency of an electrical signal.
5.2.6 Prova d'arrencada
Evaluates the vehicle's starting system.
5.2.7 Duty Cycle Test
Measures the duty cycle of a pulsed signal.
5.2.8 Prova de relés
Tests the operation of automotive relays.
5.2.9 Resistance & Diode Test
Measures resistance and tests diodes.
5.2.10 Injector Signal Test
Analyzes the signal sent to fuel injectors.
5.2.11 Activació de components
Allows for safe activation of components by providing power or ground.
5.2.12 Prova de càrrega
Checks the vehicle's charging system performance.
5.2.13 Prova de curtcircuit
Detects short circuits in the vehicle's wiring.
6. Manteniment
To ensure the longevity and accuracy of your ANCEL devices, follow these maintenance guidelines:
- Neteja: Utilitzeu un suau, damp cloth with mild soap to clean the exterior of the devices. Do not use abrasive cleaners or solvents.
- Emmagatzematge: Store the devices in a dry, clean environment, away from extreme temperatures and direct sunlight. Keep them in their original case or a protective pouch when not in use.
- Cura del cable: Inspect cables and connectors regularly for any signs of damage, fraying, or corrosion. Replace damaged cables immediately.
- Actualitzacions de programari: Periodically check the ANCEL official website for available software updates for the AD410 to ensure optimal performance and compatibility with newer vehicles.
7. Solució De Problemes
| Problema | Causa possible | Solució |
|---|---|---|
| AD410 does not power on. | Loose connection; Vehicle's DLC has no power; Blown fuse in vehicle. | Check OBD2 cable connection; Verify vehicle's DLC has power; Check vehicle's fuse box. |
| PB600 does not power on. | Incorrect battery connection; Vehicle battery too low. | Assegureu-vos que el cl vermellamp is on positive, black on negative; Check vehicle battery voltage (ha de ser de 8-35V). |
| Communication error with vehicle (AD410). | Incorrect protocol; Faulty DLC; Non-OBD2 compliant vehicle. | Verify vehicle is OBD2 compliant (1996 US, 2000 EU/Asian); Check DLC for damage; Try on another vehicle. |
| Inaccurate readings (PB600). | Poor connection; Damaged probe tip/cable. | Ensure firm contact with test point; Inspect probe and cables for damage. |
8. Especificacions
8.1 ANCEL AD410 Enhanced OBD2 Scanner
- Visualització: 2.4" TFT true-color LCD (262K)
- Vol. Operatiutage: 9-18V DC
- Protocols admesos: KWP2000, ISO9141, J1850 VPW, J1850 PWM, CAN
- Temperatura de funcionament: De 0 °C a 60 °C (32 °F a 140 °F)
- Temperatura d'emmagatzematge: -20 °C a 70 °C (-4 °F a 158 °F)
- Dimensions: Aproximadament 125 mm x 70 mm x 22 mm
8.2 ANCEL PB600 Power Circuit Probe Tester
- Vol. Operatiutage: 8-35V DC
- Visualització: LCD color
- Longitud del cable: 20 peus (aprox. 6 m)
- Protecció de sobrecàrrega: Sí
- Temperatura de funcionament: De 0 °C a 60 °C (32 °F a 140 °F)
- Temperatura d'emmagatzematge: -20 °C a 70 °C (-4 °F a 158 °F)
9. Garantia i Suport
ANCEL products typically come with a limited warranty. Please refer to the warranty card included with your product or visit the official ANCEL website for detailed warranty terms and conditions. For technical support, product inquiries, or service, please contact ANCEL customer support through their official weblloc web o la informació de contacte proporcionada amb la compra.
Official ANCEL Store: Visit the ANCEL Store on Amazon
