1. Introducció i finalview
The GREENCUT BAS370C submersible water pump is engineered for efficient and stable water extraction from deep wells, tanks, and for domestic irrigation systems. This robust pump is designed for clean water applications, offering reliable performance and ease of installation.
Característiques principals:
- Rendiment potent: 370W (0.5 HP) motor with a maximum flow rate of 20 L/min and a pumping height of up to 50m.
- Construcció duradora: Features a screw-type impeller and IP58 protection, ensuring resistance to continuous underwater operation.
- Fàcil instal·lació: Includes a 10m cable for straightforward setup in deep wells.
- Compacte i silenciós: Designed for minimal noise and easy maintenance, suitable for clean water with particles ≤ 0.2 mm and temperatures up to 35°C.
2. Instruccions de seguretat
Always prioritize safety when operating electrical equipment near water.
- Seguretat elèctrica: Ensure the power supply matches the pump's requirements (220V). All electrical connections must be secure and waterproof. Use a residual current device (RCD) for added protection.
- Mai s'assequi: Operating the pump without water will cause severe damage. Ensure the pump is fully submerged before starting.
- Qualitat de l'aigua: This pump is designed for clean water with small particles (≤ 0.2 mm) and a maximum temperature of 35°C. Do not use with dirty water, corrosive liquids, or flammable substances.
- Instal·lació: Securely attach all hoses and cables. Use a strong rope or stainless steel cable to lower and retrieve the pump, ensuring it does not rely solely on the electrical cable.
- Vàlvula antiretorn: It is highly recommended to install an external non-return valve to prevent water backflow and maintain pressure in the system. The internal non-return valve may not be sufficient for all applications.
- Emmagatzematge: Before storing, completely drain the pump of water, especially in freezing conditions. Store in a dry, protected area.
- Manteniment: Disconnect from power before performing any maintenance or cleaning.
3. Característiques del producte
The GREENCUT BAS370C pump is built with high-quality materials and thoughtful design for optimal performance.
3.1 Robust and Durable Design
Constructed from stainless steel, the pump is highly resistant to corrosion and wear, ensuring a long operational life even under continuous submersion.
3.2 Efficient Motor and Hydraulic System
Equipped with a 370W (0.5 HP) motor and a screw-type impeller, the pump delivers stable and efficient performance. Its hydraulic configuration allows it to pump up to 20 liters per minute and achieve a maximum pumping height of 50 meters.
3.3 Integrated Electrical Control Box
The pump includes an electrical control box for safe and convenient operation. This box often contains the necessary capacitor for single-phase power conversion, as noted by users.
3.4 Versatile Installation
The pump can be installed and operated in both vertical and horizontal positions, provided it is fully submerged. Top handles facilitate easy insertion and handling in wells.
4. Especificacions tècniques
| Especificació | Valor |
|---|---|
| Fabricant | Greencut |
| Número de model | 1000232 |
| Dimensions (L x A x A) | 9 x 9 x 56 cm |
| Pes | 9.5 kg |
| Poder | 370 W (0.5 HP) |
| Voltage | 220 V |
| Caudal màxim | 20 litres per minut |
| Alçada màxima d'elevació | 50 metres |
| Material | Acer inoxidable |
| Font d'alimentació | Cable elèctric |
| Longitud del cable | 10 metres |
| Classificació de protecció | IP58 |
| Temperatura màxima de l'aigua | 35 °C |
| Mida màxima de partícules | 0.2 mm |
| Components inclosos | 1x BAS370C Submersible Water Pump, 1x 10-meter Cable, 1x Electrical Control Box, 1x Instruction Manual |
5. Configuració i instal·lació
Follow these steps for proper installation of your GREENCUT BAS370C submersible pump:
- Prepareu la bomba: Ensure the pump is clean and free from any debris.
- Connect the Discharge Hose: Attach a suitable discharge hose to the pump's outlet. Secure the connection with a hose clamp per evitar fuites.
- Install Non-Return Valve: For optimal performance and to prevent water backflow, install a non-return valve in the discharge line, preferably above the pump.
- Assegureu la bomba: Attach a strong, non-corrosive rope or stainless steel cable to the pump's designated attachment points. This will be used to lower and retrieve the pump. Do not use the electrical cable for this purpose.
- Baixa la bomba: Carefully lower the pump into the well or water source, ensuring it is fully submerged. The pump can operate vertically or horizontally.
- Connexió elèctrica: Connect the pump's electrical cable to the provided electrical control box. Ensure all connections within the control box are correctly wired (main input, secondary input, ground) according to the wiring diagram in the manual. The control box typically contains a capacitor for single-phase operation.
- Font d'alimentació: Connect the control box to a suitable 220V power supply, ensuring it is protected by an RCD.
5.1 Installation Video Example
Watch this video for a visual guide on installing a deep well submersible pump (note: specific model may vary, but principles apply):
6. Instruccions de funcionament
Operating the GREENCUT BAS370C is straightforward once properly installed.
- Assegureu-vos de la submersió: Verify that the pump is completely submerged in clean water before activating.
- Activa l'alimentació: Turn on the power supply to the electrical control box. The pump should start automatically.
- Monitoritzar el rendiment: Observe the water flow and pressure. The pump is designed to provide consistent performance.
- Automatic Operation (if applicable): If your system includes an automatic pressure switch, the pump will start and stop automatically based on water demand (e.g., opening or closing a tap).
- Apagar: To stop the pump, turn off the power supply at the control box.
6.1 Operation Video Examples
These videos demonstrate the operation of similar deep well submersible pumps:
7. Manteniment
Regular maintenance ensures the longevity and optimal performance of your GREENCUT BAS370C pump.
- Neteja: Periodically inspect the pump's intake for blockages from sediment or debris. Clean as necessary.
- Hivernització: In areas prone to freezing temperatures, remove the pump from the water source, drain it completely, and store it in a dry, frost-free location.
- Cable and Hose Inspection: Regularly check the electrical cable and discharge hose for any signs of wear, damage, or leaks. Replace damaged components immediately.
- Non-Return Valve Check: If an external non-return valve is installed, periodically check its function to ensure it is preventing backflow effectively.
8. Solució De Problemes
Si teniu problemes amb la bomba, consulteu els següents problemes i solucions habituals:
| Problema | Causa possible | Solució |
|---|---|---|
| La bomba no arrenca | No power supply; Faulty electrical connection; Motor overload. | Check power outlet and circuit breaker. Inspect all electrical connections in the control box. Allow motor to cool if overloaded. |
| Baix cabal o pressió d'aigua | Partial blockage in intake or discharge hose; Insufficient water level; Faulty non-return valve; Air in the system. | Check and clear any blockages. Ensure pump is fully submerged. Inspect and replace non-return valve if necessary. Bleed air from the system. |
| La bomba funciona però no subministra aigua | Pump not submerged; Airlock; Suction hose leak; Impeller damage. | Ensure full submersion. Prime the pump if necessary. Check hose connections for leaks. Contact service if impeller is suspected to be damaged. |
| La bomba s'atura de manera inesperada | Overheating; Low water level; Electrical fault. | Allow pump to cool. Ensure adequate water level. Check electrical connections and RCD. |
9. Garantia i Suport
For any warranty claims, technical assistance, or spare parts, please contact Greencut customer service or visit their official weblloc.
Greencut Service & Support: www.greencut-tools.com
Si us plau, conserveu el comprovant de compra per motius de garantia.
