MSI PANO 130R MLG Edition ATX Mid-Tower Gaming PC Case Instruction Manual

Introducció

This manual provides detailed instructions for the installation, operation, and maintenance of your MSI PANO 130R MLG Edition ATX Mid-Tower Gaming PC Case. Please read this manual thoroughly before beginning assembly to ensure proper setup and optimal performance.

Image: The MSI PANO 130R MLG Edition PC Case, showcasing its distinctive red and black design with a panoramic tempered glass panel.

Configuració i instal·lació

Follow these steps to correctly set up your PC case and install components.

1. Desembalatge i inspecció

Carefully remove the case from its packaging. Inspect for any damage that may have occurred during transit. Verify all accessories listed in the packing list are present.

2. Instal·lació de la placa base

The PANO 130R MLG Edition supports ATX and Micro-ATX motherboards, including Back-Connect PROJECT ZERO motherboards for simplified cable management.

1. Place the motherboard onto the standoffs inside the case.
2. Fixeu la placa base amb els cargols proporcionats.

Image: Diagram illustrating the extensive compatibility for various motherboard sizes (Mini-ITX, Micro-ATX, ATX) and GPU placement within the case.

3. Instal·lació del sistema de refrigeració

This case supports up to 10 fans and a 360mm radiator on both the top and side panels for extensive cooling. Four ARGB fans are pre-installed.

1. Install additional fans or radiators as desired on the designated mounting points.
2. Assegureu-vos la direcció adequada del flux d'aire per a un rendiment de refrigeració òptim.

Image: Diagram showing the case's support for 120mm and 140mm fans, highlighting the extensive cooling options on the top and side panels.

4. Instal·lació de la unitat

The case provides support for both 3.5" and 2.5" drives.

1. Locate the drive mounting brackets.
2. Secure your 3.5" HDDs or 2.5" SSDs into the appropriate bays using the provided screws.

Image: Diagram illustrating the available drive mounting locations for 3.5-inch and 2.5-inch storage devices within the PC case.

5. Instal·lació de la font d'alimentació

La font d'alimentació es munta a la part inferior de la carcassa.

1. Slide the power supply into its designated compartment at the bottom rear of the case.
2. Secure it with screws from the rear of the case.

6. Gestió de cables

Utilize the cable routing channels and tie-down points behind the motherboard tray to organize cables. This improves airflow and aesthetics, especially with Back-Connect motherboards.

7. Connexions del panell d'E/S frontal

Connect the front panel cables (USB, audio, power, reset, ARGB) to the corresponding headers on your motherboard. Refer to your motherboard manual for specific header locations.

Imatge: Primer pla view of the front I/O panel, labeling the USB ports, audio jacks, reset button, and power button.

Instruccions de funcionament

Un cop instal·lats i connectats tots els components, podeu engegar el sistema.

1. Encès

Press the power button on the front I/O panel to start your computer. Ensure all external peripherals are connected and powered.

2. Control del ventilador ARGB

The pre-installed ARGB fans can be controlled via your motherboard's ARGB software or a dedicated controller (if included or purchased separately). Refer to your motherboard's manual for ARGB header locations and software instructions.

Manteniment

Un manteniment regular ajuda a garantir la longevitat i el rendiment òptim de la carcassa i els components del teu PC.

1. Neteja del filtre de pols

The case features magnetic top and removable bottom dust filters. These should be cleaned regularly to prevent dust buildup and maintain optimal airflow.

1. Gently remove the magnetic top filter.
2. Slide out the bottom filter.
3. Clean the filters using compressed air or by rinsing with water (ensure they are completely dry before reinstallation).

Image: Close-up showing the magnetic top dust filter and the removable bottom dust filter, highlighting the case's dust protection features.

2. Neteja general

Wipe down the exterior of the case, including the tempered glass panels and metal surfaces, with a soft, damp cloth. Avoid abrasive cleaners that could scratch the finish.

Imatge: Una panoràmica view of the MSI PANO 130R MLG Edition PC case, emphasizing its 270-degree tempered glass panel for showcasing components interns.

Resolució de problemes

Si teniu problemes, consulteu aquests consells habituals per resoldre problemes.

1. El sistema no s'encén

• Check all power connections, including the power supply unit (PSU) to the wall outlet, and internal connections to the motherboard and components.
• Assegureu-vos que el cable de l'interruptor d'alimentació del panell frontal estigui connectat correctament a la placa base.
• Verifiqueu que l'interruptor de la font d'alimentació estigui en la posició "ON".

2. Fans Not Spinning or ARGB Not Working

• Confirmeu que els cables d'alimentació del ventilador estiguin connectats correctament a la placa base o al controlador del ventilador.
• Check ARGB cables for proper connection to the motherboard's ARGB header or a dedicated controller.
• Ensure ARGB software is installed and configured correctly.

Image: Illustration of daisy-chain connections, typically used for simplifying ARGB fan wiring and control.

3. Problemes de sobreescalfament

• Netegeu els filtres de pols i els components interns per millorar el flux d'aire.
• Verify all case fans are spinning and oriented correctly for optimal intake and exhaust.
• Ensure CPU cooler and GPU fans are functioning properly.

Image: Diagram illustrating optimized airflow paths within the PC case, showing intake and exhaust points for efficient heat dissipation.

Especificacions

Key technical specifications for the MSI PANO 130R MLG Edition PC Case.