Bambu Lab H2C AMS Combo 3D Printer

INSTRUCCIONS D'ÚS DEL PRODUCTE

Si us plau, tornaview tota la guia abans d'utilitzar el producte.

Avís de seguretat:

1. No connecteu a l'alimentació fins que no s'hagi completat el muntatge.
2. Calen dues o més persones per transportar la impressora a causa del seu gran pes.

Llegeix abans d'utilitzar

Per garantir la seguretat i un rendiment òptim, seguiu aquestes pautes:

• Verifiqueu que el volum de funcionament de la impressoratage matches the specified requirements to avoid damage or safety hazards. This can be checked on the label next to the power socket. Re-fer to the “Printer Specifications” section for details.
• Regular maintenance is essential to keep the printer’s complex mechanisms running smoothly. For guidance, see the “Regular Maintenance” section. Please complete initial calibration first and then install induction hotends to the induction hotend rack.
• Please use the right hotend to print TPU, and the left hotend to print PPS/PPA-CF. For other types of filament, there are no such restrictions. We recommend that you check our Wiki for more information and get a better printing experience.
• La impressora canvia els hotends automàticament; eviteu canviar-los manualment per evitar possibles danys.
• For best results, we recommend using Bambu filaments, which have been rigorously tested for compatibility, safety, and stability with the product.
• To prevent the filament from getting stuck, do not print flexible filaments such as TPU with a hardness level of 95A or below 95A, or damp PVA or BVOH with the feeder unit filament inlet of the AMS 2 Pro.
• The AMS 2 Pro supports a spool width between 50 mm to 68 mm and a diameter between 197 mm to 202 mm. We recommend using plastic spools.
• You can use the drying function of the AMS 2 Pro using only a 6-pin cable to connect it to an H2 series printer. If you need to dry filaments in multiple AMS 2 Pro units, you need to purchase official Bambu Lab power adapters to power the drying function of the other AMS 2 Pro units.
• During the filament drying process, the AMS 2 Pro removes moisture through external air circulation via the air inlets. Please ensure the air intake and vent are not blocked to ensure optimum drying efficiency.

Introducció als components de la impressora

Introducció al component del capçal d'eines

Induction hotend rack component introduction

Stickers are attached below the assemblies to indicate their numbers. As shown above, the numbers are 1 to 6 from left to right.

Introducció al component AMS 2 Pro

Accessoris inclosos

Remove the package. Keep packaging materials and screws for shipping.

1. Traieu la caixa d'accessoris i retireu el cartró, l'escuma i la cinta adhesiva que l'envolten.
2. Remove the stickers from the sides and the top opening of the moisture-proof bag. Then, pull the bag downward and fold it over all four corners of the bottom cardboard.
3. Ensure the bottom cardboard stays in place. With two people, carefully lift the printer out of the cardboard and moisture-proof bag, and place it on a stable surface.
4. Remove the adhesive tapes and other packaging materials. Then, take out the top glass cover and set it aside.

Desbloqueja l'AMS 2 Pro

1. Use the longer H2.0 allen key from the accessory box to remove the 4 screws marked in red. Next, detach the two plastic parts from the top.
2. Use the H2.0 allen key to remove the 2 screws marked in red. Then, carefully take out the AMS 2 Pro.
3. Use the H2.0 allen key to remove the 4 screws marked in red. Then, take out the fixture and the nearby foam (except the foam under the heatbed).

Desbloqueja el llit de calefacció

• Use the H2.0 allen key to remove the 4 screws marked in red to unlock the heatbed.
• The toam under the heatbed can be removed only after the calibration process is completed.

Unlock the induction hotend rack

Desbloqueja el capçal de l'eina

Cut and remove all zip ties. Pull the toolhead toward the front of the printer, then remove the foam piece marked in green.

Place the desiccant in the AMS 2 Pro

1. Take out the accessories in the AMS 2 Pro.
2. Remove the foam from inside the AMS 2 Pro.
3. Remove the tape from the back of the AMS 2 Pro and take out the desiccant packs. Then, remove the outer plastic packaging. Install 2 desiccant packs on each side of the empty compartment.

Instal·leu l'AMS 2 Pro

1. Place the top glass cover and the AMS 2 Pro on top of the printer.
2. Take out the PTFE tube from the accessory box, insert the PTFE tube into the AMS 2 Pro’s filament outlet and any PTFE tube coupler of the printer, and push the tube forward for ap- approximately 10 cm until it stops (if you can see the PTFE tube from the window next to the buffer from the front of the printer (it is correctly inserted).
   • The upper coupler corresponds to the right hotend, and the lower one to the left hotend.
   • Connect one or more AMS 2 Pro units to allow the hotends to print in multiple colors.
   • Instal·leu l'AMS 2 Pro
3. Connect the Bambu Bus Cable 6-pin to the printer and either the 6-pin port of the AMS 2 Pro.

Install multiple AMS 2 Pro units (optional)

If you have more than one AMS 2 Pro, you can connect them to the right hotend to utilize multiple induction hotends to reduce waste when changing filament.

1. Take out a short PTFE tube from the accessory box. Connect it to the 4-in-1 PTFE adapter and the upper PTFE tube coupler of the printer. Ensure to push the PTFE tube until it cannot move forward.
2. Use the longest PTFE tubes to connect the filament outlet of AMS 2 Pro units and the 4-in-1 PTFE adapter.
3. Use a 6-pin cable to connect any AMS 2 Pro and the printer.
4. Use 6-pin cables to connect the remaining AMS 2 Pro units in pairs.
5. If you need to use the drying function of the AMS 2 Pro units, each unit will require an official Bambu Lab power adapter, except for the one directly connected to the printer.

Instal·leu el porta-bobines

• Take out the spool holder from the accessory box, and slide it in place as shown above.
• The screws holes marked in green near the bottom of the printer can also be used to install a spool holder bracket, allowing you to add a spool holder and print with two external spools of filament simultaneously.
• The package includes 1 bracket and a spool holder by default.

Carregar el filament des d'una bobina externa

If the printer is connected to the AMS 2 Pro on a coupler, you can feed filament from an external spool using the additional coupler.

1. Connect one end of the PTFE tube to the spool holder’s PTFE tube coupler and the other end to the printer’s other coupler, pushing it in until it stops.
2. Insert the filament into the PTFE tube and continue pushing until it enters the extruder and can no longer move forward.

Instal·leu la clau de seguretat

• Take out the safety key on the rear panel, and insert it into the installation slot located above the power socket.
• Si us plau, no us salteu aquest pas, ja que la impressora no es pot engegar sense ell.

Connecteu el cable d'alimentació i engegueu-lo

Connecteu el cable d'alimentació a la presa de corrent de la part posterior. A continuació, engegueu l'interruptor.

Enquadernar la impressora – Bambu Handy

1. Scan the QR code on the right to download Bambu Handy. Reg- ister and log in to your Bambu Lab account.
2. Segueix les instruccions de la pantalla fins que aparegui un codi QR.
3. Escaneja el codi QR de Bambu Handy per vincular la impressora al teu compte de Bambu Lab.
4. Seguiu les instruccions de la pantalla per completar el calibratge inicial. És normal que hi hagi vibracions i soroll durant el procés.
   • NO traieu l'escuma que hi ha sota la base calefactora fins que no s'hagi completat el calibratge.

Enquadernar la impressora – Bambu Studio

1. Connect both the computer and printer to the same wireless network, and do not use a guest network that has network device separation enabled.
2. Visita l'enllaç següent per descarregar i instal·lar Bambu Studio. Registra't i inicia la sessió al teu compte de Bambu Lab. bambulab.com/download/studio
3. Click “+” on the device page, and Bam-bu Studio automatically discovers printers on the same network. Click the detected printer to bind it to your Bam-bu Lab account.

Install induction hotends

After the initial calibration completes, take out the induction hotends from the accessory box and install them on the rack. The printer can use up to 6 induction hotends, but you can only install up to 5 on the rack so that the one on the toolhead can be placed during hotend switching. Also, if hotends with different diameters are installed, you can only print with hotends with the same diameter. Please remember to take off all induction hotends before using the laser function, as dust can cause them to malfunction.

Primera impressió amb l'AMS 2 Pro

1. Engegueu la impressora i col·loqueu una bobina de filament a qualsevol de les quatre ranures. Assegureu-vos que la bobina estigui correctament col·locada a l'eix de suport actiu, tal com es mostra a la imatge.
2. Empenyeu la pestanya de l'alimentador cap al carret i inseriu el filament. L'AMS 2 Pro el precarregarà després que el detecti. Quan el llum LED de l'alimentador sota l'entrada del filament estigui encès, l'AMS 2 Pro està a punt per imprimir.
3.  Seleccioneu – Imprimir Files, then select a model you wish to print. * The textured PEL plate that comes with the printer is sensitive to dirt and oil. If you have touched the surface of the plate with your hands, oils from your hands can transfer to the surface and impact the plate’s adhesion properties. It is recommended to wash it with hot water and detergent first to ensure the best adhesion.

Primera impressió amb l'AMS 2 Pro

Notes posteriors a la impressió

• Espereu fins que la placa de construcció es refredi completament per treure les impressions.
• Renteu la placa de construcció regularment amb aigua calenta i detergent per a una millor adherència.
• If there is a support structure used, remove it as soon as possible after taking down the print. It will be harder to remove if the filament absorbs moisture.

Manteniment regular

• A 3D printer has a complex mechanical structure and numerous moving parts. Regular maintenance-
• Maintenance is essential to ensure stable operation and high-quality prints.

Peces mòbils metàl·liques:

• Lubriqueu regularment els cargols de guia, les varetes lineals, els rails de guia, les politges tendidores i els engranatges de l'extrusora per evitar l'oxidació.
• Utilitzeu oli lubricant per a rails guia, varetes lineals i politges tensores, i apliqueu greix lubricant als cargols principal i als engranatges de l'extrusora.

Consumibles:

• Inspect plastic and rubber parts, such as filament cutters, for signs of wear, deformation, or aging
• Substituïu les peces consumibles segons calgui, com ara els netejadors de broquets i els tubs de PTFE, per mantenir la qualitat d'impressió.

Induction hotend:
Regularly use a brush to grip a nozzle, cleaning sponge dipped in water to remove any filament stuck on the hotend surface to ensure optimal print quality.

Altres components:

• Reviseu les lents de la càmera, els ventiladors i els sensors de filament per si hi ha pols o restes.
• Clean fans regularly; gently clean camera lenses using a microfiber cloth dipped in isopropyl or dehydrated alcohol for optimal clarity.
• Regularly remove filament residue in the 4-in-1 PTFE adapter and replace the filament cleaning pad.

Especificacions de la impressora

* To ensure the heatbed quickly reaches the needed temperature, the printer will maintain maximum power for about 3 minutes.

AMS 2 Pro specifications

* Filaments marked with “*” require a higher drying temperature. The AMS 2 Pro cannot dry them completely. If you want better drying performance for these filaments, we recommend purchasing an AMS HT.

Suport tècnic
If you need technical support, please follow any of the following methods: Mètode 1: Visit the Bambu Lab Wiki for tutorials and maintenance guidance.
wiki.bambulab.com/homeMètode 2: Get in touch through one of the options listed in the Con-  tact Us section of our Support Center. bambulab.com/support

Mètode 3: Crea un tiquet de suport a Bambu Handy, des de la secció Centre de suport.

Video Guide quickly. bambulab.com/h2c-quick-start Scan the QR code to watch a step-by-step video and get started

Descarrega Bambu Handy i Bambu Studio
Escaneja el codi QR per descarregar Bambu Handy o visita l'enllaç següent per descarregar Bambu Studio. Pots controlar la impressora de forma remota i supervisar les teves impressions en temps real tant al telèfon com a l'ordinador. bambulab.com/download

Explora més models genials
Scan the QR code to visit MakerWorld, our models community, where you can find a variety of free models, and quickly bring your ideas to life using the creativity tools in MakerLab and accessories in Maker’s Supply. makerworld.com

Learn with Bambu Academy
Scan the QR code to visit Bambu Academy and explore printer and software courses from beginner to advanced levels to enhance your 3D printing skills.bambulab.com/support/academy

 

Preguntes freqüents

Q: How can I contact Bambu Lab Support Center?

A: You can reach out to the Bambu Lab Support Center through the contact information provided on their official weblloc.

Documents/Recursos

	Bambu Lab H2C AMS Combo 3D Printer [pdfGuia de l'usuari 20251028, 1.5, 2.0, H2C AMS Combo 3D Printer, H2C, AMS Combo 3D Printer, Combo 3D Printer, 3D Printer, Printer
	Bambu Lab H2C AMS Combo 3D Printer [pdfGuia de l'usuari 20251202, H2C AMS Combo 3D Printer, H2C AMS, Combo 3D Printer, 3D Printer, Printer

Referències

• Manual d'usuari