BSEED W-SD Multi Function Power Meter
funció clau
Presentació del producte
The multi – functional Wlfl guide rail meter adopts a rail – type design, which is small in size, compact instructure and simple in installation; it uses an LCD display screen to display current, voltage, electricity, power,frequency and other electrical parameters, is convenient for users to acquire data and easy to operate. It hasgood anti – electromagnetic interference capabilities, meets various needs of power management, facilitates therealizationof terminal – intelligent power metering, and facilitates the retrofitting of power meters in the lateltransformation of the lighting system. It is widely used in commercial squares, science and technology parksuniversities and other occasions where billing is required, It can also be jointly deployed with energyconsumption monitoring and energy management systems. its application scope includes property bilingmanagement, electricity metering, power demand – side management, energy management andenergy-saving analysis, Other low – voltage power systems, etc.
Paràmetres tècnics
| Voltage | AC 220V/110v |
| Vol. Operatiutage gamma | AC 80V-300V |
| Freqüència | 50/60Hz |
| Interval de potència | 0-99999 kWh |
| Interval de temps | 0-999 dies |
| Factor de potència | 0-1.0PF |
| Interval de temperatura | -40-150°C |
| Overvoltage rang de configuració | 130-300V |
| Undervoltage rang de configuració | 75-21ov |
| Overcurrent setting range | 1-63A |
| Overpower setting range | 1-15 kW |
| Aïllament nominal voltage | 400 V |
| Contactes de sortida | 1NO |
| Vida mecànica | 10,000 vegades |
| Classe de protecció | lp30 |
| Altitud | ::,2000m |
| Humitat | 550%at40°C(non-condensing) |
Function Introduction, Default Settings
| Opcions | Interval de configuració | Paràmetres per defecte |
| Overvoltage
protecció |
230-300V | 270 V |
| Undervoltage
protecció |
110-21ov | 170 V |
| Sobreintensitat
protecció |
0.1-63A | 40A |
| Protecció de sobrecàrrega | 1-15 kW | 8. 8KW |
| Energia elèctrica
protecció |
0-99999 kWh | 99999kwh |
| Supervisió
protecció |
0-150°( | 85 °C |
| Number of closures | 1-30 vegades | 5 vegades |
| Closingtime | 1-600 segons | 30 segons |
| Electricityclearing | On/Off | apagat |
| Timing clearing | On/Off | apagat |
| Power-up operation | Close/open/hold | mantenir |
| Overvoltagedelay
protecció |
1-600 sec/off | apagat |
| Undervoltagedelay
protecció |
1-600 sec/off | apagat |
| Overcurrent delay
protecció |
1-600 sec/off | apagat |
| Overloaddelay
protecció |
1-600 sec/off | apagat |
| Supervisió
delayprotection |
1-600 sec/off | apagat |
structural analysis
DIMENSIONS
Mida del producte
Diagrama de cablejat
Set function operation
Press the set key for 5 seconds to enter the settings page, give an example of the “Overvoltage Protection” setting, click the
key cursor to move to the “Overvoltage Protection” position, press the set key to select, press the
key to adjust to the required value, press the set to save after the adjustment is completed, and press the key to select other settings. If you do not need to set it, press the
key to move the cursor to the exit position, and then press set to return to the home page. The other settings can be the same as the “Overvoltage Protection” setting method.
Set function operation
Descarregueu l’aplicació Smart Life 
or Graffiti APP Smart Connection
WIFI connection or reset operation method: Long press the wifi key 5-10s wifi indicator light will flash, turn on the phone Bluetooth, then open the Smart Life APP, click “+” in the upper right corner, select “Add Device”, wait for the device to scan out the device, click on the device to select the wifi name, enter the password to wait for the device to be added successfully.
MÉS INFORMACIÓ
Documents/Recursos
 |
BSEED W-SD Multi Function Power Meter [pdfManual d'instruccions wifi_1p_din_rail, W-SD Multi Function Power Meter, W-SD, Multi Function Power Meter, Function Power Meter, Power Meter, Meter |