HP HCETS Software

Especificacions del producte

• Software: HCETS Interface Beta
• Files Loaded on /5C: CET, CSO, MSG HPIL, KEYS
• Compatibility: 82161A Cassette Drive

Instruccions d'ús del producte

Reloading Procedures

1. Press the ATN key to get the prompt.
2. Type >COPYTECHMOD: CA to load Techmod file.
3. After loading, press RUN to start the HCETS program.

Creating New Software Strips:

1. With 75C connected to the cassette, press the ATN key to get the prompt.
2. Type >COPYMAKECARD: CA to load.
3. Follow program prompts to create new strips. Protect each track after creating all tracks of a file.

Purging Load File:

1. After creating software strips, remember to purge the load file.
2. Example: When prompted ‘create another set?’ type NO. SThe screenwill display a reminder message.
3. Press the RUN key to restart the HCETS program.

* NEW HCETS SOFTWARE *

INSTRUCCIONS D'INSTALLACIÓ

1. THROW OUT OLD HCETS SOFTWARE STRIPS!
2. CONNECT YOUR 75C TO AN 82161A CASSETTE DRIVE LOADED WITH “HCETS INTERFACE BETA”.
3. CTL, SHIFT, CLR TO CLEAR EXISTING PROGRAM FROM 75C. HOLD UNTIL THE SCREEN GOES BLANK.
4. ATN: SET DATE AND TIME. £J’t.T
5. TYPE THE FOLLOWING COMMANDS:
   • ASSIGNIO”: CA”
   • COPY”CASSLOAD: CA” TO “LOAD11
   • RUN”LOAD”
   • TECH NUMBER=> your 5 or 6 digit tech#
   • FIREMAN PASSWORD=> your tech#
   • 75C PASSWORD=> your own choice
6. 75C WILL BE LOADED WITH THE FOLLOWING FILES: CET, CSO, MSG, HPIL, KEYS.
7. ATN KEY TO GET PROMPT.
   • COPY”TECHMOD: CA” TO “TECHMOD”.
     Això file allows the ce t o press the tab key and have the after-hours software techmod load in directly from memory. No need to pull strips. Caution: this file reduces cso capacity from 9 to 7.
     You may load TechMod strip after pressing tab to save space for additional cso/s. Do not load this file if you do not have after-hours support.
8. THIS COMPLETES THE RELOAD FROM THE CASSETTE DRIVE. PRESS RUN TO START HCETS PROGRAM.
9. TO MAKE A NEW SET OF SOFTWARE STRIPS, FOLLOW THE INSTRUCTIONS BELOW.
10. WI TH 75C CONNECTED TO CASSETTE-.-1
    ATN KEY TO GET PROMPT.
    • COPY”MAKECARD: CA” TO “LOAD”
    • RUN”LOAD”
      Follow program prompts. When creating strips, you must protect each track after al I tracks of a file are created. A file is complete when you are prompted to create the next file.
11. NEW AFTER MAKING A SET OF SOFTWARE STRIPS, REMEMBER TO PURGE THE LOAD FILE.
    Example: last prompt “create another set”? Type NO. Screen wi 11 display a reminder message and go blank. Press the RTN key for the prompt.
    • PURGE 11 LOAD 11
      PRESS RUN KEY FOR RESTART OF HCETS PROGRAM 1.
12. THIS COMPLETES THE PROCEDURES FOR LOADING THE NEW HCETS SOFT-! WARE. READ THE ATTACHED HCETS! I  INTERFACE MATERIAL.

Preguntes freqüents

How do I know if I need to load the Techmod file?

Load the Techmod file only if you have after-hours support and want to reduce CSO capacity.

What should I do if the screen does not go blank after clearing existing programs?

Ensure that you are holding down CTL + SHIFT + CLR until the screen goes blank before proceeding further.

Documents/Recursos

hp HCETS Software [pdfGuia d'instal·lació HCETS Software, Software

Referències

• Manual d'usuari