igloo EK2 Keypad 2
Què s'inclou
- A: Keypad
- B: Mounting Plate
- C: Mounting Screws
- D: Anchor Bolt
- E: Torx (T10) Screwdriver
- F: Battery Cover
Passos d'instal·lació
Muntatge amb cargols
Find a place to install your Keypad. Installing it closer to your locks and entryway will enable easier operation.
El que necessites
- Step 1: Separate the Mounting Plate
Separate the mounting plate (B) from the keypad (A) by loosening the screw from below. Use the supplied Torx (T10) Screwdriver (E). - Step 2: Select Install Location
The Keypad 2 should be installed 86cm – 120cm (34 – 48 in) above the ground to ensure ADA compliance. Ensure that the keypad is not more than 5m away from the linked lock to ensure strong connectivity. 
Step 3: Mark Mounting Holes
Mark out two holes for securing the mounting plate (B). Use the mounting plate or Drill Sheet as a reference for marking the holes. The distance between the holes should be 80 mm / 3.15 in.
- PAS 4
IMPORTANT To ensure secure installation, use the recommended pilot hole and anchor bolt guidelines below. Mounting Pilot Hole Anchor Surface Diameter Bolt? Wood 2 mm / 5/64″ X Sheetmetal 2 mm / 5/64* X Brick 6 mm / 15/64″ D Concrete 6 mm / 15/64″ Masonry 6 mm/15/64″ D Drywall 6 mm/15/64″ *The pilot holes should be drilled to a depth of 50mm / 2″
- Step 5: Insert Anchors if Required
Insert anchor bolts if required. Secure the mounting bracket (B) by tightening the mounting screws (C).
- Step 6:Secure Mounting Bracket.
- Pas 7: Inseriu les bateries
- Carefully remove the battery cover (F) by loosening the two screws with the Torx (T10) screwdriver (E).
- Carefully replace the battery cover (F) by tightening the two battery screws with the Torx (T10) Screwdriver.
- Place the Keypad (A) onto the mounting plate (B) as shown. Secure it with the Torx (T10) screwdriver (E) from below.
- Step 8: Assemble the Keypad
Això és!
You have now installed your Keypad 2 device. Please download the igloo works app to proceed with pairing.
Característiques
Control any igloo Lock
Harness the power of no-tour PIN Codes & NFC credentials on multiple igloo locking devices.
Dissenyat per a la durabilitat
With an IK-09 Impact & IP66 Protection, the Keypad 2 is designed for heavy use.
Works for Everyone
Whether using PIN codes or key fobs, Keypad 2 eliminates reliance on mobile devices.
Control de volum
Ajusteu el volum segons les vostres preferències. Seleccioneu entre els nivells 0 (silenciat) al 5 (més fort).
Fàcil instal·lació
A zero-wiring setup means your Keypad can be online within minutes. Can be mounted on a variety of surfaces with anchors and fasteners for wood, brick, drywall, concrete and masonry.
Flexible NFC Credential Suite
Create duration, permanent or scheduled NFC access on physical fobs or mobile devices.
Physical Keypad
Accessible, tactile buttons built for zero-error input.
Alerta de bateria baixa
Les alertes visuals i d'àudio intuïtives us demanaran que canvieu les piles quan s'esgotin.
Bloqueig de seguretat
Keypad is disabled after several incorrect access attempts to ensure your property is always secure.
Audio and LED Indicators
| Accions | Indicacions |
|---|---|
| Unlocked Successfully | Status LED flashes Blue |
| Tancat | Status LED blinks Green, 4 fast ascending tones. |
| Incorrect Credential | Status LED blinks Green, single long beep. |
| Reached max. no. of digits (16) | Status LED blinks RED, 4 short beeps. |
| Security Lockout Activated | Status LED blinks RED, low-high siren for 30 /60 / 90 seconds. 2 long beeps. |
| Bloqueig de seguretat desactivat | Status LED breathes RED when woken up, 3 fast descending tones. |
| Alerta de bateria baixa | Status LED blinks BLUE, 3 short beeps. |
| Hard Reset Mode | Status LED blinks RED, GREEN, BLUE, 4 slow descending tones. 2 slow beeps, 2 fast beeps. |
| Reinicialització/desvinculació | Status LED blinks RED, GREEN, BLUE, 4 slow descending tones. |
| Engegada de potència | 2 slow beeps, 2 fast beeps. |
Documents/Recursos
 |
igloo EK2 Keypad 2 [pdfGuia d'instal·lació 2AYD7-EK2, EK2 Keypad 2, EK2, Keypad 2 |