inno IMX708 Camera Module
Descripció
Acabatview
- CAM-IMX708AF Camera Module Feature with Sony IMX708 Sensor, Autofocus lens, IR-filter, Compatible with Raspberry Pi Camera Module 3 Standard Version.
- CAM-IMX708AF can be used to take full HD video as well as stills photographs and feature an HDR mode up to 3 megapixels. It carries IR cut filter. Its operation is fully supported by the libcamera library, including Camera Module 3’s rapid autofocus feature: this makes it easy for beginners to use, while offering plenty for advanced users. Camera Module 3 is compatible with all Raspberry Pi computers.
- CAM-IMX708AF Camera Module Third Generation: Back-illuminated and stacked CMOS 12-megapixel image sensor (IMX708) with HDR for up to 3-megapixel output
- High-quality Image Output: 4608 × 2592 pixels, carrying IR cut filter, along with built-in 2D DPC and QBC Re-mosaic function, offering high SNR
- Autofocus System: Phase detection autofocuses
- CSI-2 serial Data Output: 2-wire serial communication, supporting I2C fast mode and fast-mode plus
Característiques
- Back-illuminated, stacked CMOS 12-megapixel IMX708 image sensor
- High signal-to-noise ratio (SNR), built-in 2D dynamic defect pixel correction (DPC)
- Phase detection autofocus (PDAF) for rapid autofocus
- Camp diagonal de view: 75 degrees, common video modes: 1080p50, 720p100, 480p120, output RAW10
- Supports Raspberry PI5, PI4, PI3
ESPECIFICACIÓ
| Sensor | Sony IMX708 |
| Resolució | 11.9 megapíxels |
| Mida del sensor | Diagonal del sensor de 7.4 mm |
| Mida de píxels | 1.4 μm × 1.4 μm |
| Common video modes | 1080p50, 720p100, 480p120 |
| Sortida | RAW10 |
| Filtre IR | Sí |
| Autofocus system | Autofocus de detecció de fases |
| Dimensions | 32x32mm(12.4mm height for Wide variants) |
| Longitud del cable de cinta | 150 mm |
| Connector de cable |
|
Maquinari
Mida de la càmera 
Camera Module Pins Out
 |
||||
| PIN # | Nom | Descripció | ||
| 1 | GND | Terra | ||
| 2 | CAM_D0_N | MIPI Data Lane 0 Negative | ||
| 3 | CAM_D0_P | MIPI Data Lane 0 Positive | ||
| 4 | GND | Terra | ||
| 5 | CAM_D1_N | MIPI Data Lane 1 Negative | ||
| 6 | CAM_D1_P | MIPI Data Lane 1 Positive | ||
| 7 | GND | Terra | ||
| 8 | CAM_CK_N | MIPI Clock Lane Negative | ||
| 9 | CAM_CK_P | MIPI Clock Lane Positive | ||
| 10 | GND | Terra | ||
| 11 | CAM_IO0 | Habilita l'alimentació | ||
| 12 | CAM_IO1 | Indicador LED | ||
| 13 | CAM_SCL | I2C SCL | ||
| 14 | CAM_SDA | I2C SDA | ||
| 15 | CAM_3V3 | Entrada d'alimentació de 3.3 V |
Autofocus Lens Information
| Interval d'enfocament | 10 cm–∞ |
| Distància focal | 4.74 mm |
| Diagonal f ield of view | 75 graus |
| Horizontal f ield of view | 66 graus |
| Vertical f ield of view | 41 graus |
| Focal ratio (F-stop) | F1.8 |
| IR-Filter | Sí |
Connexió 
Programari
Modificar config.txt
- sudo nano /boot/config.txt
- For the latest version raspberry Pi OS, it should be
- sudo nano /boot/firmware/config.txt
Add the content below to the last line
- dtoverlay=imx708
- Canvia a
- camera_auto_detect=1
- a
- camera_auto_detect=0
Reboot and use below command to preview
libcamera-hello -t 0
Documentació
- Camera Description on Raspberry Pi
- Camera Software On Raspberry Pi
CONTACTE AMB NOSALTRES
- Suport: support@inno-maker.com
- Preu a granel: sales@inno-maker.com
- Viqui: wiki.inno-maker.com
- Github: https://github.com/INNO-MAKER
| Data | Revisió | Canvia els detalls |
| 2024/09/08 | V1.0 | Primer llançat |
Preguntes freqüents
Is the CAM-IMX708AF Camera Module compatible with all Raspberry Pi models?
Yes, the camera module is compatible with Raspberry Pi 5, Pi4, and Pi 3 models.
What autofocus system does the camera module use?
The camera module uses Phase Detection Autofocus (PDAF) for rapid focusing.
Documents/Recursos
 |
inno IMX708 Camera Module [pdfManual d'usuari CAM-IMX708AF, IMX708 Camera Module, IMX708, Camera Module, Module |