LTECH Mini Pro LED Dimmer Controller Kit Instruction Manual

LTECH Mini Pro LED Dimmer Controller Kit

LED Dimmer Controller Kit

• Compact and lightweight, with a housing made from
• Covestro/Samsung V0-rated flame-retardant PC material;
• Features a soft-start gradual dimming function for greater visual comfort;
• Uses a 2.4GHz RF wireless signal, eliminating the need for signal cables;
• Ultra-sensitive touch brightness ring for adjusting brightness;
• Includes a brightness shortcut function for one-touch switching between brightness levels;
• A single remote control can manage an unlimited number of controllers within its effective range;
• Controllers within the same group or zone feature dynamic synchronization;
• LED status indicators provide operational feedback.

Especificacions tècniques

M1A+P1

• Control remot
  • M1A
• Color del producte
  • Blanc
• Tipus de regulació
  • DIM
• Tipus sense fil
  • RF 2.4 GHz
• Vol. Operatiutage
  • 3 VDC (1 CR2032 button cell battery)
• Corrent d'espera
  • <2UA
• Interval de control remot
  • 30 meters (under ideal conditions)
• Temp. de funcionament
  • -25°C~50°C
• Pes del producte
  • 40 g + 5 g
• Dimensions
  • 104×58×9mm (remote control) 108×63×14 mm (remote control+backrest)
• Controlador
  • P1
• Senyal d'entrada
  • RF2.4GHz
• Entrada Voltage
  • 12-48V
• Vol. De sortidatage
  • 12-48V
• Nombre de canals
  • 1 canal
• Interruptor de restabliment
  • Sí
• Corrent de càrrega
  • Màx. 11A
• Potència de càrrega
  • 132W@12 240W@24V 28W@36V 384W@48V
• Protecció
  • Short-circuit, over-temperature, overcurrent, and reverse connection protection
• Pes del producte
  • 46 g + 5 g
• Dimensions
  • L91 × W37 × H21 (mm)

Dimensions del producte

• Unitat: mm

Instal·lació del producte

Two ways to fix the remote holder:

1. Fixeu el suport del comandament a la paret amb dos cargols.
2. Fix the remote holder in the wall with 3M adhesive.
   • Nota: Si us plau, estireu la pestanya de la bateria abans del primer ús

Bateria de recanvi

1. Use a screwdriver to unscrew the bottom screw.
2. Pull out the battery compartment and replace the battery.
3. Tighten the screw after replacing the battery

Característiques

• Potència: Encén o apaga la llum.
• Brillantor Touch Ring: Touch to change the light’s brightness.
• Brillantor +/-: Adjusts the brightness; short press for 11 levels; long press for 1-6 seconds for 255 levels of continuous adjustment.
• Brillantor Shortcut Key: 25%, 50%, 75%, 100%.
• Escena: Short press to recall a scene; long press for 2 seconds to save the current light state to the scene.

Esquema de cablejat

Maridatge

Maridatge de botons

1. Briefly press the ID learning button on the controller. The load indicator will flash. Please complete the following steps within 10 seconds.
2. Mini Pro Series Single-Zone Remote Control with Pairing:
   • Press and hold the power button until the controller’s load indicator flashes rapidly and then stays lit, and the color ring changes when touched.
   • La programació està completa.

ID Learning Key

Power-on synchronization

1. After the controller has been powered off and then powered back on, please complete the following steps within 10 seconds.
2. Mini Pro Series Single-Zone Remote Control with Pairing:
   • Press and hold the power button until the controller’s load indicator flashes rapidly and then stays lit, and the color ring changes when touched.
   • La programació està completa.

Nota: A single controller can pair with up to 10 remote controls. If more than 10 remote controls are paired, the ID code of the first remote control will be automatically deleted.

Esborra el codi

How to delete all remote controls:

• Press and hold the “Learn” button on the controller for 6 seconds. The controller’s load indicator will flash quickly four times and then remain lit, indicating that the code has been successfully cleared.

ID Learning Key

Precaucions d'instal·lació

• Please do not stack the products. The distance between two products should be> 15 cm so as not to affect heat dissipation and the lifespan of the products.
• Do not fix the product tightly against the wooden board with screws. Please add a washer ≥7 mm thick under the mounting screws to leave a gap for effective heat dissipation and to avoid affecting the heat dissipation and service life of the product.
• Do not allow the product to come into large-area contact with metal objects (e.g. keel frames). The separation distance shall be ≥15 cm to avoid signal interference affecting operation.
• Do not place the product on top of a power supply. The distance between the product and the power supply should be ≥15 cm so as not to affect heat dissipation and the lifespan of the product.
• Please do not place the products on the floor. The distance between the product and the floor should be> 100 cm to avoid signal interference.
• Please do not install the products on beams or near the corners. The distance between the product and the beam or the corner should be> 15 cm so as to avoid signal interference.

INSTRUCCIÓ DE SEGURETAT

Atencions

• La instal·lació i posada en marxa del producte l'ha de fer un professional qualificat.
• Products are and not lightning proof non-waterproof (special models excepted). Please avoid the sun and rain. When installed outdoors, please ensure they are mounted in a waterproof enclosure or in an area equipped with lightning protection devices.
• Una bona dissipació de calor allargarà la vida útil del producte. Instal·leu el producte en un entorn amb bona ventilació.
• During installation, avoid being close to large-area metallic objects or stacking the devices to prevent signal interference from affecting the usage.
• Eviteu instal·lar-ho en zones propenses a tempestes, zones amb camps magnètics forts i zones d'alt volumtage àrees.
• Quan instal·leu aquest producte, eviteu estar a prop d'una gran àrea d'objectes metàl·lics o apilar-los per evitar interferències de senyal.
• Si us plau, comproveu si el volum de treballtagEl seu ús compleix els requisits de paràmetres del producte.
• Before you power on the product, please make sure all the wiring is correct in case of incorrect connection that may cause a short circuit and damage the components, or trigger an accident.
• Si es produeix un error, no intenteu arreglar el producte per vosaltres mateixos. Si teniu cap pregunta, poseu-vos en contacte amb el proveïdor.
• The contents of this manual are subject to change without prior notice. In case of any discrepancy between the description and actual functions, the physical product shall prevail. Please feel free to contact us.

Acord de garantia

• Warranty period from the date of delivery: 5 years.
• Els serveis de reparació o substitució gratuïts per problemes de qualitat es proporcionen dins dels períodes de garantia.

A continuació, s’exclouen les garanties:

• Més enllà dels períodes de garantia.
• Qualsevol dany artificial causat per alt voltage, sobrecàrrega o operacions inadequades.
• Productes amb danys físics greus.
• Danys causats per catàstrofes naturals i força major.
• Les etiquetes de garantia i els codis de barres s'han danyat.
• No contract signed by our company.
  • Repair or replacement provided is the only remedy for customers. Our company is not liable for any incidental or consequential damage unless it is within the law.
  • Our company has the right to amend or adjust the terms of this warranty, and any release in written form shall prevail.