MOONS NPSUGMDHB Wireless Node Controller Owner’s Manual

MOONS NPSUGMDHB Wireless Node Controller

Especificacions

• Customer’s Part Number:
• MOONS’ Part Number: 4696355000211
• Model: NPSUGMDHB
• P/N: A8768

Subjecte a canvis sense previ avís

DESCRIPCIONS

• The Wireless Node Controllers can be installed in the lighting control box, lamp chamber or installed self-contained under eaves or other sheltered areas due to the solid metal enclosure.
• It is very small size and excellent waterproof.
• It can automatically identify different types of LED driver, such as 0-10V, DALI-2/D4i and DMX(RDM).
• Supports 2 channels 0-10V for color temperature adjustment.
• Supports RGBW color.
• Supports dynamic scenes and animations.
• It communicates with the gateway through a WPAN (Sub-GHz).
• Self-building and self-healing MESH Network.
• The sensor interface supports sensor access with digital and analog outputs.

CARACTERÍSTIQUES

• Vol d’entradatage:12-30VDC.
• Power consumption: < 1W.
• Wireless communication: IEEE 802.15.4-915MHz.
• Automatically identify dimming mode.
• DMX(RDM) master, up to 6 loads.
• DALI-2/D4i Single-Master Controller, up to 6 loads.
• 2 channels of 0-10V Dimmer, up to 4 loads each channel.
• RGBW color support
• Dynamic scenes and animations
• 1 channel of sensor sampl'entrada.
• Save several dimming plans.
• Firmware upgrade: OTA.
• Embedded communication encryption mechanism.
• Radio frequency certification: FCC
• Warranty: 5years.

CARACTERÍSTIQUES

 CARACTERÍSTIQUES ELÈCTRIQUES
At 20 ℃, 50% RH, 100Kpa conditions.

Nota:

1. In the case of DALI-2/D4i mode, the input voltage needs to be higher than the DALI BUS voltage.
2. Quan l'entrada voltage is 12V, 0-10V can output 10V at most; When the output voltage is > 12V, 0-10V can output 11V.

Condicions de funcionament

EMC

Certificació

Dades mecàniques

Dimensions
Dimensions are provided in the diagrams above.

Antena

 Accessoris opcionals

ETIQUETA 

Product barcode information:

• The last 8 digits of SN represent the communication address of the product.
• A” indicates that this product operates in the American frequency band;
• The QR code shows the product’s communication address.

Descripcions de funcions

Interfícies

WPAN Module

• Communicate with the Gateway. Transfer various instructions, such as: dimming command, upload power metering data, set parameters and query telemetries accordingly and so on.
• Wireless communication: IEEE 802.15.4-Sub-GHz.
• Embedded communication encryption mechanism.

Atenuació
Once the device is powered up, it will automatically identify the dimming mode (DALI-2/D4i / DMX(RDM) /0-10V) of the connected load. After recognition, it will automatically report its own running dimming mode and perform necessary operation in this way.

Avís: To achieve perfect recognition of the dimming type, it is recommended that the controller and the LED driver be powered on simultaneously, or the controller be powered on later than the LED driver.

Atenuació de 0-10 V

• If it is identified as 0-10V dimmer, it can support 2-channel independent 0-10V dimming, which can support adjusting the color temperature (tunable white LED driver and software configuration are required).
• The DIM-TO-OFF LED drivers should be used; the LED drivers’ output will turn off once the dimming voltage és < 0.5 V.
• Support positive and negative logic dimming (configuration required).
• If each channel is connected to multiple LED drivers, the maximum output current of each channel is 10mA, and if the load current is >10mA, the output voltage will be not accurate.

Avís: Quan l'entrada voltage is 12V, 0-10V can output 10V at most; When the output voltage is > 12V, 0-10V can output 11V.

DMX(RDM)

• If identified as a DMX(RDM) master, it can support up to 6 loads (maximum 3 slots for each load) and can be automatically addressed to support RDM instructions.
• 4 loads are recommended.

DALI-2/D4i

• If identified as a DALI-2/D4i Single-Master Controller, up to 6 loads (one address for each load) can be supported, supporting IEC62386-101/103/251/252/253/351 (TYPE D).
• 4 loads are recommended.

Avís:

• At least one of the DALI-2/D4i LED drivers needs to be set to supply power to the DALI bus.
• Maximum of 6 DALI-2/D4i LED Drivers, any DALI-2/D4i LED Drivers >4 will need the power supply disabled
• In the case of DALI-2/D4i mode, the input voltage needs to be higher than the DALI BUS voltage.

Entrada del sensor

• 1 channel of sensor input interface.
• Sensors with 0-10V output can be accessed.
• Passive digital output can be accessed.
• Sensors must be configured in software before it is functional in system.

Llums indicadores

Avís: 

1.  Purple light indicates that the communication between node controller and LED driver is lost. This might be due to use wrong LED driver or LED driver is not power on or wiring error (for example the reverse connection of the DMX bus). Please check the wiring connection or the power-on status of the LED driver, and then re-power the node controller.

INSTAL·LACIÓ

For DALI-2/D4i applications with sensor

For DMX(RDM) applications with sensor 

For 0-10V Dim to off applications with sensor 

 For 0-10V Tunable white applications with sensor 

 Recommended installation of antenna interface 

 Recommended installation of M18 Antenna 

COMANDES

Declaració de la FCC

Aquest dispositiu compleix la part 15 de les normes de la FCC. El funcionament està subjecte a les dues condicions següents:

1. Aquest dispositiu no pot causar interferències perjudicials i
2. Aquest dispositiu ha d'acceptar qualsevol interferència rebuda, incloses les interferències que puguin provocar un funcionament no desitjat.

Precaució: S'adverteix a l'usuari que els canvis o modificacions no aprovats expressament per la part responsable del compliment poden anul·lar l'autoritat de l'usuari per fer servir l'equip.

Nota: Aquest equip s'ha provat i s'ha comprovat que compleix els límits per a un dispositiu digital de classe B, d'acord amb la part 15 de les normes de la FCC.

Aquests límits estan dissenyats per proporcionar una protecció raonable contra interferències nocives en una instal·lació residencial. Aquest equip genera usos i pot irradiar energia de radiofreqüència i, si no s'instal·la i s'utilitza d'acord amb les instruccions, pot provocar interferències perjudicials a les comunicacions de ràdio. Tanmateix, no hi ha cap garantia que no es produeixin interferències en una instal·lació concreta. Si aquest equip provoca interferències perjudicials a la recepció de ràdio o televisió, cosa que es pot determinar apagant i encenent l'equip, es recomana a l'usuari que intenti corregir la interferència mitjançant una o més de les mesures següents:

• Reorienta o reubica l'antena receptora.
• Augmentar la separació entre l'equip i el receptor.
• Connecteu l'equip a una presa d'un circuit diferent d'aquell al qual està connectat el receptor.
• Consulteu el distribuïdor o un tècnic de ràdio/TV amb experiència per obtenir ajuda.

Per mantenir el compliment de les directrius d'exposició a RF de la FCC, aquest equip s'ha d'instal·lar i fer funcionar amb una distància mínima entre 20 cm del radiador del seu cos: Utilitzeu només l'antena subministrada.

CUSTOMER’S APPROVAL STAMP
Please sign back after your approval. The specifications will come into force when we receive purchase order.

Subjecte a canvis sense previ avís
© 2024 MOONS’. All rights reserved. All content contained herein is subject to change without prior notice. More product documentation and MOONS’ terms and conditions are available at https://www.moonsindustries.com

History Version