THIRD REALITY ZB2 Smart Button User Manual

Smart Button ZB2
Guia d'inici ràpid

Contingut del paquet

Especificacions

Restabliment de fàbrica

Press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.

Setting up your Smart Button ZB2

1. Follow instructions to set up your compatible Zigbee hub.
2. Use the Micro-USB charging cable included in the package to connect the button to a power adapter (not included) to active the Smart Button ZB2.
3. You can also press and hold buttons 1 and 2 for 10 seconds, the Smart Button ZB2 will be activated once it beeps three times. The device will automatically enter pairing mode.
   Note: It will exit pairing mode automatically if not successfully paired within 3 minutes, to put it into pairing mode again, press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.
4. After the pairing is completed, the device will beep once. you can create routines in the corresponding smart home App or platform to control other connected devices. THIRDREALITY Smart Button ZB2 features three buttons (button 1 & button 2 & button  3), each supporting three control settings: Pressed, Double Pressed and Held. Note: When charging, please connect the button to a power adapter (not included) using the Micro-USB charging cable provided in the package. The Smart Button ZB2 will be fully charged until it beep twice.

Escaneja el codi QR a view detalls

https://bit.ly/488mkj9

Resolució de problemes

1. How to check if the device is fully charged
   The Smart Button ZB2 will be fully charged until it beep twice.
2. El dispositiu no s'encén
   Recharge the battery, ensure it powers on properly, and note that low temperatures may reduce performance.
3. Cannot charge / No charging response
   Use the original charger, check the charging port, and wait a few minutes in case of over-discharge protection.

Conformitat amb la normativa de la FCC
Aquest dispositiu compleix la part 15 de les normes de la FCC. El funcionament està subjecte a les dues condicions següents: (1) Aquest dispositiu no pot causar interferències perjudicials i (2) aquest dispositiu ha d'acceptar qualsevol interferència rebuda, incloses les interferències que puguin provocar un funcionament no desitjat.
Qualsevol canvi o modificació no aprovat expressament per la part responsable del compliment podria anul·lar l'autoritat de l'usuari per fer servir l'equip.
Nota: Aquest equip s'ha provat i s'ha comprovat que compleix els límits per a un dispositiu digital de classe B, d'acord amb la part 15 de les normes de la FCC.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the  instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by  turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorienta o reubica l'antena receptora.
– Augmentar la separació entre l'equip i el receptor.
– Connecteu l'equip a una presa de corrent d'un circuit diferent d'aquell al qual està connectat el receptor.
– Consulteu el distribuïdor o un tècnic de ràdio/TV amb experiència per obtenir ajuda.
The device has been evaluated to meet general RF exposure requirement. The device can be used in the exposure condition without restriction. 06

Per obtenir una garantia limitada, visiteu
https://thirdreality.com/faq-help-center/
Per obtenir assistència al client, poseu-vos en contacte amb nosaltres a
info@3reality.com o visita www.thirdreality.com
For questions on other platforms, visit the corresponding
platform’s application/support platform.