Youpu YP06A Module Owner’s Manual

Youpu YP06A Module

Acabatview

• The YP06A module supports Zigbee 3.0 and BLE 5.0 protocols, featuring 132KBRAM, 192KB ROM, 1Kb eFuse, and a maximum clock frequency of 144MHz. Figure 1(a and b) below shows the module schematic diagram.

Descripció de la interfície

PIN interface

The 11PIN pad interface specifications are detailed in Table 1 below:

Punts de prova

As shown in Figure 1(b), the test points on the back of the module are used for product manufacturing testing and debugging purposes, as detailed in Table 2 below:

Paràmetres clau

See Table 3 below for the main parameters of the module.

Dimensions mecàniques

Refer to Figure 2 below for the module’s mechanical dimensions.

Embalatge

Refer to Figure 3 below for details. PCB encapsulation is recommended.

• Double-sided PCB Top clearance zone
• Double-sided PCB Bottom (mirror image)

Antena

1. Tipus d'antena
   The YP06A module is a surface-mount ceramic antenna.
2. Descripció de l'antena

To maximize the radiation performance of the antenna, the following recommendations are advised:

1. The spatial three-dimensional distance between the module antenna area and metal components of user products (such as housing positioning screws, power supply wires, signal conductors, hardware parts, etc.) must be at least 6-15 mm.
2. The user’s PCB board must not have traces or copper-clad layers in the 6mm area directly beneath the module antenna region and its surroundings.
3. The module is positioned at one corner or side of the product, with the antenna area facing outward toward the user.

Contacta amb nosaltres

• Companyia weblloc:
• Business and Technical Support: 15996846172

The others information

• Identificador FCC: 2BOSO-YP06A
• ID IC: 33844-YP06A
• HVIN: YP06A

Declaració de la FCC

Normes de la FCC: FCC CFR Títol 47 Part 15 Subpart C Secció 15.247

1. Aquest dispositiu no pot causar interferències perjudicials.
2. aquest dispositiu ha d'acceptar qualsevol interferència rebuda, incloses les interferències que puguin provocar un funcionament no desitjat.

Qualsevol canvi o modificació no aprovat expressament per la part responsable del compliment podria anul·lar l'autoritat de l'usuari per fer servir l'equip. Nota: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct th interference by one or more of the following measures:

• Reorienta o reubica l'antena receptora.
• Augmentar la separació entre l'equip i el receptor.
• Connecteu l'equip a una presa d'un circuit diferent d'aquell al qual està connectat el receptor.
• Consulteu el distribuïdor o un tècnic de ràdio/TV amb experiència per obtenir ajuda.

Declaració d'exposició a la radiació de la FCC

• The module can be installed or integrated into mobile or fixed devices. This module cannot be installed in any portable device if without further certification, such as C2PC with SAR. This module complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This module must be installed and operated with a minimum distance of 20 cm between the radiator and user’s body. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter
• Module FCC ID: 2BOSO-YP06A Or Contains
• FCC ID: 2BOSO-YP06A” The devices must be installed and used in strict accordance with the manufacturer’sinstructions as described in the user documentation that comes with the product.
• Any company of the host device that installs this module with modular approval should perform the test of radiated & conducted emission, spurious emission, etc.
• According to FCCpart15BClass B requirement, only if the test result complies with FCC Part 15B Class B requirement, then the host can be sold legally.
• When the module is installed inside another device, the user manual of the host must contain the above information
• Paragraphs A, B, and C contain warning statements.

DECLARACIÓ IC

• A: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operations are subject to the following two conditions:

1. Aquest dispositiu no pot causar interferències.
2. This device must accept any interference, including interference that may causeundesired operation of the device

Declaració d'exposició a la radiació IC

• This module complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This module must be installed and operated with a minimum distance of 20
• Si el número IC no és visible quan el mòdul s'instal·la dins d'un altre dispositiu, l'exterior del dispositiu on s'instal·la el mòdul també ha de mostrar una etiqueta que faci referència al mòdul inclòs. Aquesta etiqueta exterior pot utilitzar paraules com la següent:
  • “Contains IC: 33844-YP06A”
• When the module is installed inside another device, the user manual of this device must contain
• Above paragraph warning statements. The devices must be installed and used in strict accordance with the manufacturer’sinstructions as described in the user documentation that comes with the product

Resolució de problemes

This section will be populated with common issues and their solutions. As this is the first draft, specific troubleshooting steps are not yet available.

• El mòdul no s'encén: Check the 3V3 and GND connections. Ensure the supply voltage is within the 2.7V to 3.5V range.
• Communication issues (UART): Verify RX/TX connections (GPIO18/GPIO17). Ensure correct baud rates and serial port settings.
• Flash programming failure: Check the BOOT pin state during power-on. Ensure the TX-LOG (GPIO14) and RX-LOG (GPIO15) connections are correct for debugging.
• Poor RF performance: Review antenna placement guidelines. Ensure no metal obstructions or PCB traces are within the recommended clearance zones around the antenna.